5秒后页面跳转
捷配首页

Datasheet > 电源电路 > 线性稳压器IC> ADP1711AUJZ-1.15R7
ADP1711AUJZ-1.15R7 PDF预览

ADP1711AUJZ-1.15R7

更新时间： 2024-01-19 13:32:44
品牌 Logo 应用领域
亚德诺 - ADI 线性稳压器IC调节器电源电路光电二极管输出元件
页数 文件大小 规格书
16页 422K
描述
150 mA, Low Dropout, CMOS Linear Regulator

阅读下载

获取价格

ADP1711AUJZ-1.15R7 技术参数

是否无铅： 不含铅是否Rohs认证： 符合
生命周期：Active零件包装代码：TSOT
包装说明：VSSOP,针数：5
Reach Compliance Code：unknown风险等级：5.67
最大回动电压 1：0.3 V最大输入电压：5.5 V
最小输入电压：2.5 VJESD-30 代码：R-PDSO-G5
JESD-609代码：e3长度：2.9 mm
湿度敏感等级：1功能数量：1
端子数量：5工作温度TJ-Max：125 °C
工作温度TJ-Min：-40 °C最大输出电流 1：0.15 A
最大输出电压 1：1.173 V最小输出电压 1：1.127 V
标称输出电压 1：1.15 V封装主体材料：PLASTIC/EPOXY
封装代码：VSSOP封装形状：RECTANGULAR
封装形式：SMALL OUTLINE, VERY THIN PROFILE, SHRINK PITCH峰值回流温度（摄氏度）：260
调节器类型：FIXED POSITIVE SINGLE OUTPUT LDO REGULATOR座面最大高度：1 mm
表面贴装：YES技术：CMOS
端子面层：MATTE TIN端子形式：GULL WING
端子节距：0.95 mm端子位置：DUAL
处于峰值回流温度下的最长时间：40宽度：1.6 mm
Base Number Matches：1

ADP1711AUJZ-1.15R7 数据手册

 浏览型号ADP1711AUJZ-1.15R7的Datasheet PDF文件第1页浏览型号ADP1711AUJZ-1.15R7的Datasheet PDF文件第2页浏览型号ADP1711AUJZ-1.15R7的Datasheet PDF文件第4页浏览型号ADP1711AUJZ-1.15R7的Datasheet PDF文件第5页浏览型号ADP1711AUJZ-1.15R7的Datasheet PDF文件第6页浏览型号ADP1711AUJZ-1.15R7的Datasheet PDF文件第7页 
ADP1710/ADP1711  
SPECIFICATIONS  
VIN = (VOUT + 0.5 V) or 2.5 V (whichever is greater), IOUT = 1 mA, CIN = COUT = 1 μF, TA = 25°C, unless otherwise noted.  
Table 1.  
Parameter  
Symbol  
VIN  
Conditions  
Min  
Typ  
35  
Max  
Unit  
V
INPUT VOLTAGE RANGE  
OPERATING SUPPLY CURRENT  
TJ = –40°C to +125°C  
2.5  
5.5  
IGND  
IOUT = 0 μA  
μA  
μA  
μA  
μA  
μA  
μA  
mA  
mA  
μA  
μA  
%
IOUT = 0 μA, TJ = –40°C to +125°C  
IOUT = 100 μA  
50  
40  
IOUT = 100 μA, TJ = –40°C to +125°C  
IOUT = 100 mA  
80  
665  
1
IOUT = 100 mA, TJ = –40°C to +125°C  
IOUT = 150 mA  
860  
1.3  
IOUT = 150 mA, TJ = –40°C to +125°C  
EN = GND  
SHUTDOWN CURRENT  
IGND-SD  
VOUT  
0.1  
EN = GND, TJ = –40°C to +125°C  
IOUT = 1 mA  
1.0  
FIXED OUTPUT VOLTAGE ACCURACY  
(ADP1710 AND ADP1711)  
–1  
–2  
+1  
100 μA < IOUT < 150 mA, TJ = –40°C to +125°C  
IOUT = 1 mA  
+2  
%
ADJUSTABLE OUTPUT VOLTAGE  
ACCURACY (ADP1710 ADJUSTABLE)1  
LINE REGULATION  
VOUT  
0.792 0.8  
0.784  
0.808  
0.816  
+0.1  
V
100 μA < IOUT < 150 mA, TJ = –40°C to +125°C  
VIN = (VOUT + 0.5 V) to 5.5 V, TJ = –40°C to +125°C  
IOUT = 10 mA to 150 mA  
V
∆VOUT/∆VIN  
∆VOUT/∆IOUT  
–0.1  
%/ V  
%/mA  
LOAD REGULATION2  
0.002  
IOUT = 10 mA to 150 mA, TJ = –40°C to +125°C  
IOUT = 100 mA, VOUT ≥ 3.0 V  
0.004 %/mA  
mV  
DROPOUT VOLTAGE3  
VDROPOUT  
100  
150  
120  
180  
IOUT = 100 mA, VOUT ≥ 3.0 V, TJ = –40°C to +125°C  
IOUT = 150 mA, VOUT ≥ 3.0 V  
175  
250  
200  
300  
mV  
mV  
mV  
mV  
mV  
mV  
mV  
IOUT = 150 mA, VOUT ≥ 3.0 V, TJ = –40°C to +125°C  
IOUT = 100 mA, 2.5 V ≤ VOUT < 3.0 V  
IOUT = 100 mA, 2.5 V ≤ VOUT < 3.0 V, TJ = –40°C to +125°C  
IOUT = 150 mA, 2.5 V ≤ VOUT < 3.0 V  
IOUT = 150 mA, 2.5 V ≤ VOUT < 3.0 V, TJ = –40°C to +125°C  
START-UP TIME4  
TSTART-UP  
ADP1710  
80  
μs  
ADP1711  
CURRENT LIMIT THRESHOLD5  
With 10 nF bypass capacitor  
TJ rising  
100  
270  
150  
μs  
ILIMIT  
180  
360  
mA  
THERMAL SHUTDOWN THRESHOLD  
TSSD  
°C  
°C  
V
THERMAL SHUTDOWN HYSTERESIS  
UVLO ACTIVE THRESHOLD  
UVLO INACTIVE THRESHOLD  
UVLO HYSTERESIS  
TSSD-HYS  
UVLOACTIVE  
15  
VIN falling  
1.95  
1.8  
UVLOINACTIVE VIN rising  
UVLOHYS  
2.45  
V
250  
mV  
V
EN INPUT LOGIC HIGH  
VIH  
2.5 V ≤ VIN ≤ 5.5 V  
EN INPUT LOGIC LOW  
VIL  
2.5 V ≤ VIN ≤ 5.5 V  
EN = IN or GND  
0.4  
1
V
EN INPUT LEAKAGE CURRENT  
VI-LEAKAGE  
0.1  
30  
μA  
ADJ INPUT BIAS CURRENT  
(ADP1710 ADJUSTABLE)  
ADJI-BIAS  
OUTNOISE  
100  
nA  
OUTPUT NOISE  
ADP1710  
10 Hz to 100 kHz, VOUT = 3.3 V  
330  
40  
μVrms  
μVrms  
ADP1711  
10 Hz to 100 kHz, VOUT = 0.75 V, with 10 nF bypass capacitor  
POWER SUPPLY REJECTION RATIO  
ADP1710  
PSRR  
1 kHz, VOUT = 3.3 V  
58  
69  
dB  
dB  
ADP1711  
1 kHz, VOUT = 0.75 V, with 10 nF bypass capacitor  
1 Accuracy when OUT is connected directly to ADJ. When OUT voltage is set by external feedback resistors, absolute accuracy in adjust mode depends on the tolerances  
of resistors used.  
2 Based on an end-point calculation using 10 mA and 150 mA loads. See Figure 8 for typical load regulation performance for loads less than 10 mA.  
3 Dropout voltage is defined as the input-to-output voltage differential when the input voltage is set to the nominal output voltage. This applies only for output  
voltages above 2.5 V.  
4 Start-up time is defined as the time between the rising edge of EN to OUT being at 90% of its nominal value.  
5 Current limit threshold is defined as the current at which the output voltage drops to 90% of the specified typical value. For example, the current limit for a 1.0 V  
output voltage is defined as the current that causes the output voltage to drop to 90% of 1.0 V, or 0.9 V.  
Rev. 0 | Page 3 of 16  
 
 
1234567...16

下载PDF

与ADP1711AUJZ-1.15R7相关器件

型号 品牌 描述 获取价格 数据表
ADP1711AUJZ-1.2-R7 ADI 150 mA, Low Dropout, CMOS Linear Regulator

获取价格
ADP1711AUJZ-1.3-R7 ADI 150 mA, Low Dropout, CMOS Linear Regulator

获取价格
ADP1711AUJZ-1.5-R7 ADI 150 mA, Low Dropout, CMOS Linear Regulator

获取价格
ADP1711AUJZ-1.8-R7 ADI 150 mA, Low Dropout, CMOS Linear Regulator

获取价格
ADP1711AUJZ-2.5-R7 ADI 150 mA, Low Dropout, CMOS Linear Regulator

获取价格
ADP1711AUJZ-3.0-R7 ADI 150 mA, Low Dropout, CMOS Linear Regulator

获取价格

与ADP1711AUJZ-1.15R7相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证