5秒后页面跳转
AD8240YRMZ PDF预览

AD8240YRMZ

更新时间: 2024-01-17 14:01:50
品牌 Logo 应用领域
亚德诺 - ADI 驱动器监控
页数 文件大小 规格书
12页 258K
描述
LED Driver/Monitor

AD8240YRMZ 技术参数

是否无铅: 含铅是否Rohs认证: 不符合
生命周期:Active零件包装代码:TSSOP
包装说明:MO-187AA, MSOP-8针数:8
Reach Compliance Code:not_compliantECCN代码:EAR99
HTS代码:8542.39.00.01风险等级:5.05
接口集成电路类型:LED DISPLAY DRIVERJESD-30 代码:S-PDSO-G8
JESD-609代码:e0长度:3 mm
湿度敏感等级:1复用显示功能:NO
功能数量:1区段数:1
端子数量:8最高工作温度:125 °C
最低工作温度:-40 °C封装主体材料:PLASTIC/EPOXY
封装代码:TSSOP封装形状:SQUARE
封装形式:SMALL OUTLINE, THIN PROFILE, SHRINK PITCH峰值回流温度(摄氏度):240
认证状态:Not Qualified座面最大高度:1.1 mm
最大供电电压:27 V最小供电电压:9 V
标称供电电压:13.5 V表面贴装:YES
温度等级:AUTOMOTIVE端子面层:Tin/Lead (Sn/Pb)
端子形式:GULL WING端子节距:0.65 mm
端子位置:DUAL处于峰值回流温度下的最长时间:NOT SPECIFIED
宽度:3 mmBase Number Matches:1

AD8240YRMZ 数据手册

 浏览型号AD8240YRMZ的Datasheet PDF文件第2页浏览型号AD8240YRMZ的Datasheet PDF文件第3页浏览型号AD8240YRMZ的Datasheet PDF文件第4页浏览型号AD8240YRMZ的Datasheet PDF文件第6页浏览型号AD8240YRMZ的Datasheet PDF文件第7页浏览型号AD8240YRMZ的Datasheet PDF文件第8页 
AD8240  
PRODUCT DESCRIPTION  
The AD8240 consists of four functional blocks labeled A  
through D, as shown in Figure 2.  
HIGH-SIDE CURRENT-SENSE AMPLIFIER WITH  
OPEN LED DETECTION (BLOCK B)  
VPLUS  
VO  
This amplifier is used to measure the LED current by ampli-  
fying the voltage across a user-selected shunt resistor. It has a  
gain of 24 and an overall accuracy of 5%. The output of the  
amplifier is typically connected to a microcontroller A/D  
converter input so that the condition of the LED lamp can be  
determined. This output can also be tied to other devices such  
as a latching comparator or output buffer. It is important to note  
that the output of this amplifier has a relatively high impedance  
of approximately 10 kΩ. As a result, a buffer amplifier should be  
used if the load is less than 100 kΩ.  
SHUNT BASE  
B
VSENSE  
C
A
5V  
REFERENCE  
D
PWM  
COMPARATOR WITH LATCH-OFF OVERCURRENT  
PROTECTION (BLOCK C)  
AD8240  
GND  
This block is used to shut down the output in the case of a  
short circuit or an overcurrent condition. When the output  
of the high-side current-sense amplifier approaches 5 V, the  
comparator output switches, causing the driver to latch off the  
output voltage.  
Figure 2. Simplified Functional Block Diagram  
Table 3 briefly describes the blocks, while the sections that  
follow provide more detailed information.  
Table 3.  
Block  
Description  
INTELLIGENT DRIVER (BLOCK D)  
A
B
C
D
Linear regulator  
High-side current-sense amplifier  
Comparator  
The intelligent driver provides multiple functions:  
Level shifts and conditions the output of the regulator  
amplifier to drive an external user-selected power  
transistor.  
Driver  
LINEAR REGULATOR (BLOCK A)  
Accepts PWM input so that LED brightness can be  
controlled by a user-supplied PWM signal.  
The simplified architecture of the linear regulator block is an  
amplifier and resistor divider. One input to the amplifier is  
tied to the 5 V reference. The other input is tied to a resistor  
divider that sets the ratio of the 5 V reference to VO. As a  
result, the accuracy of the voltage output is proportional to  
the accuracy of the 5 V reference. For example, if the 5 V  
reference is 5% high (5.25 V), the output is 5% high (12.6 V).  
The PWM input can also be used as a simple on/off  
control for applications that do not require variable  
brightness.  
Latch-off input that latches the output off when the  
comparator trips during an overcurrent event. The latch  
is reset by cycling the PWM input.  
Rev. 0 | Page 5 of 12  
 
 
 

与AD8240YRMZ相关器件

型号 品牌 描述 获取价格 数据表
AD8240YRMZ-R7 ADI LED Driver/Monitor

获取价格

AD8240YRMZ-REEL ADI LED DISPLAY DRIVER, PDSO8, MO-187AA, MSOP-8

获取价格

AD8240YRMZ-REEL7 ADI LED DISPLAY DRIVER, PDSO8, MO-187AA, MSOP-8

获取价格

AD8244 ADI Single-Supply, Low Power, Precision FET Input Quad Buffer

获取价格

AD8244ARMZ ADI Single-Supply, Low Power, Precision FET Input Quad Buffer

获取价格

AD8244ARMZ-R7 ADI Single-Supply, Low Power, Precision FET Input Quad Buffer

获取价格