Datasheet > 5B39-02

5B39-02

更新时间： 2022-11-24 21:41:48

品牌	Logo	应用领域
亚德诺 - ADI		/
页数	文件大小	规格书
8页	690K
描述
Isolated Current Output

阅读下载

获取价格

数据手册

如果您发现信息不准确，欢迎纠错

5B39-02 数据手册

5B39

GENERAL DESCRIPTION

track-and-hold input circuit. Selected by a high Write Enable

The 5B39 is a single-channel signal conditioning module that

converts a high-level analog input voltage into a floating,

isolated proportional output current of 4 to 20 mA or 0 to 20

mA across loads from 0Ω to 750Ω. The module provides high

accuracy of +0.05%, low nonlinearity of +0.02%, and the

protection of 1500V rms isolation between output-to-input and

output-to power supply. The input common must be held to

within +1V of power common.

input, the hold mode exhibits an output droop rate of 80 uA/s.

This corresponds to a refresh interval of 25 ms for 0.01% span

droop. On power-up, the module’s output remains at 0 mA for

about 100 ms to allow the user to initialize the track-and-hold

circuit.

In applications using one DAC per channel, where the track-

and-hold feature of the 5B39 is not used, the Write Enable input

should be set to low by grounding it to power common, as on

the 5B01 and 5B08 backplanes. The module current output will

then track its input signal.

Signal isolation by transformer coupling uses a proprietary

modulation technique for linear, stable and reliable

performance. A demodulator on the output side of the signal

transformer recovers the original signal, which is then filtered

and converted to an accurate current output by a current (V-to-

I) converter output stage. Output protection enables the 5B39 to

withstand accidental connection to 240V rms power lines

without damage, while isolating computer-side circuitry. In

addition, the 5B39 is mix-and-match and hot-swappable with

all 5B Series modules, so can be inserted or removed from any

socket in the same backplane without disrupting system power.

Generating A Voltage Output Signal – The 0 to 20 mA output

of the 5B39-04 and the 5B39-03, can produce a 0 to +10V

output by connecting a 500Ω conversion resistor across the

modules’ output terminals,. This approach should be used with

caution because the output lacks the low impedance of a true

voltage source. This means that the tolerance and size of the

load impedance relative to the conversion resistor can introduce

significant error. For example, a load impedance < 500kΩ would

contribute <0.1% error.

Track-and-Hold for DAC Applications – In applications where

a single system digital-to-analog converter (DAC) is used to

drive a number of current output channels, the 5B39 includes a

Figure 2

Rev. 0 | Page 2 of 8

123 4 5 6 7 8

下载PDF

与5B39-02相关器件

型号	品牌	描述	获取价格	数据表
5B39-03	ADI	Isolated Current Output	获取价格
5B39-04	ADI	Isolated Current Output	获取价格
5B40	ADI	Isolated, Wide Bandwidth Millivolt and Voltage Input	获取价格
5B40-01	ADI	Isolated, Wide Bandwidth Millivolt and Voltage Input	获取价格
5B40-01-NI	ADI	Analog Circuit	获取价格
5B40-02	ADI	Isolated, Wide Bandwidth Millivolt and Voltage Input	获取价格