3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN
class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing
(QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-PRF-38535
may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval
in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make
modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device. These
modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-PRF-38535 is
required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
MIL-PRF-38535, appendix A and herein.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure .1
3.2.3 Truth table. The truth table shall be as specified on figure 2.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are as
specified in table I and shall apply over the full ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests
for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in
1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN number
is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to
MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in accordance
with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to listing
as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-38535, appendix
A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided with
each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
SIZE
STANDARD
MICROCIRCUIT DRAWING
5962-88715
A
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
REVISION LEVEL
C
SHEET
4
DSCC FORM 2234
APR 97
5秒后页面跳转
TLP250光耦合器：资料手册参数分析
DA14580 低功耗蓝牙系统级芯片(SoC)：资料手册参数分析
INA226 高精度电流和功率监控器：资料手册参数分析
SI2302 N沟道MOSFET：资料手册参数分析
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
