150D
Vishay Sprague
®
Solid-Electrolyte TANTALEX Capacitors
Hermetically-Sealed, Axial-Lead
STANDARD REEL PACKAGING SPECIFICATIONS - MEETS EIA STANDARD RS-296 in inches [millimeters]
"A"
13.0 [330.2]
Tape Spacing
STANDARD REEL
B
COMPONENT
SPACING
1.126 to 3.07
[28.6 to 78.0]
I.D. REEL HUB
A
1.374 to 3.626
[34.9 to 92.1]
0.031 [0.79] MAX.
OFF CENTER (1.a)
0.625 0.062 DIA.
[15.88 1.575]
THRU HOLE
0.125 [3.18] MAX.
0.250 [6.35] (3.b)
0.750 [19.05]
SECTION "A" - "A"
"A"
LABEL (4.a)
0.031 [0.79] (3.f)
BOTH SIDES (3.f)
LEAD SIZE
COMPONENT
SPACING
UNITS PER REEL
TYPE 150D UNITS WITH
INSULATING SLEEVE
TAPE
SPACING
CASE
CODE
D
L
AWG NO. NOM. DIA.
A
B
0.135 0.016 0.286 0.031
[3.43 0.41] [7.26 0.79]
0.020
24
0.200 0.015
[5.08 0.38]
2.500 0.062
[63.5 1.57]
1000
1000
500
A
B
R
S
[0.51]
0.185 0.016 0.474 0.031
[4.70 0.41] [12.04 0.79]
0.020
24
0.200 0.015
[5.08 0.38]
2.500 0.062
[63.5 1.57]
[0.51]
0.289 0.016 0.686 0.031
[7.34 0.41] [17.42 0.79]
0.025
22
0.400 0.015
[10.16 0.38]
2.875 0.062
[73.03 1.57]
[0.64]
0.351 0.016 0.786 0.031
[8.92 0.41] [19.96 0.79]
0.025
22
0.400 0.015
[10.16 0.38]
2.875 0.062
[73.03 1.57]
500
[0.64]
STANDARD REEL PACKAGING INFORMATION
f. A row of components must be centered between tapes
0.047" [1.19mm]. In addition, individual components may
deviate from center of component row 0.031" [0.79mm].
g. Staples shall not be used for splicing. Not more than 4
layers of tape shall be used in any splice area and no tape
shall be offset from another by more than 0.031" [0.79mm]
1. Component Leads:
a. Component leads shall not be bent beyond 0.047"
[1.19mm] maximum from their nominal position when
measured from the leading edge of the component lead at
the inside tape edge and at the lead egress from the
component.
b. The 'C' dimension shall be governed by the overall length
of the reel packaged component. The distance between
flanges shall be 0.125" to 0.250" [3.18mm to 6.35mm]
greater than the overall component length.
non-cumulative. Tape splices shall overlap at
l e a s t
6.0" [152.4mm] for butt joints and at least 3.0" [76.2mm]
for lap joints and shall not be weaker than unspliced tape.
Universal splicing clips may also be used.
h. Quantity per reel shall be controlled so that tape
components and cover shall not extend beyond the smallest
dimension of the flange (either across flats or diameter).
Once the quantity per reel for each part number has been
established, future orders for that part number shall be
packaged in that quantity. When order or release quantity
is less than the established quantity, a standard commercial
pack is to be used.
2. Orientation:
a. All polarized components must be oriented to one direction.
The cathode lead tape shall be a color and the anode lead
tape shall be white.
3. Reeling:
a. Components on any reel shall not represent more than two
date codes when date code identification is required.
b. Component leads shall be positioned between pairs of
0.250" [6.35mm] tape.
i. A maximum of 0.25% of the components per reel quantity
may be missing without consecutive missing components.
c. The disposable reels have hubs and corrugated fiber board
flanges and core or equivalent.
d. A minimum of 12.0" [304.8mm] leader of tape shall be
provided before the first and after the last component on
the reel.
e. 50 or 60 lb. Kraft paper must be wound between layer of
components as far as necessary for component protection.
Width of paper to be 0.062" to 0.250" [1.57mm to 6.35mm]
less than the 'C' dimension of the reel.
j. Adequate protection must be provided to prevent physical
damage to both reel and components during shipment and
storage.
4. Marking:
a. Minimum reel and carton marking shall consist of the
following: Customer Part Number, Purchase Order No.,
Quantity, Package Date, Manufacturer's Name, Electrical
Value, Date Code, Vishay Sprague Part Number and
Country of Origin.
Document Number: 40015
Revision 13-Jun-02
For technical questions, contact tantalum@vishay.com
www.vishay.com
19