5秒后页面跳转
110IMX7-05-05-8 PDF预览

110IMX7-05-05-8

更新时间: 2024-02-24 13:14:18
品牌 Logo 应用领域
BEL /
页数 文件大小 规格书
14页 480K
描述
7-Watt DC-DC Converters

110IMX7-05-05-8 技术参数

是否Rohs认证: 不符合生命周期:Active
包装说明:PACKAGE-9Reach Compliance Code:unknown
ECCN代码:EAR99风险等级:5.24
其他特性:ADDITIONAL 5V OUTPUT ALSO AVAILABLE模拟集成电路 - 其他类型:DC-DC REGULATED POWER SUPPLY MODULE
认证:UL, CSA效率(主输出):82%
高度:8.25 mm最大输入电压:150 V
最小输入电压:60 V标称输入电压:110 V
JESD-30 代码:R-XDMA-T9JESD-609代码:e0
长度:48 mm最大电网调整率:1%
最大负载调整率:3%功能数量:1
输出次数:2端子数量:9
最高工作温度:85 °C最低工作温度:-40 °C
最大输出电流:0.6 A最大输出电压:5.05 V
最小输出电压:4.95 V标称输出电压:5 V
封装主体材料:UNSPECIFIED封装代码:DIP
封装形状:RECTANGULAR封装形式:MICROELECTRONIC ASSEMBLY
峰值回流温度(摄氏度):NOT SPECIFIED认证状态:Not Qualified
子类别:Power Supply Modules表面贴装:NO
技术:HYBRID温度等级:INDUSTRIAL
端子面层:Tin/Lead (Sn/Pb)端子形式:THROUGH-HOLE
端子位置:DUAL处于峰值回流温度下的最长时间:NOT SPECIFIED
最大总功率输出:7 W微调/可调输出:NO
热身时间:0.5 s宽度:23 mm
Base Number Matches:1

110IMX7-05-05-8 数据手册

 浏览型号110IMX7-05-05-8的Datasheet PDF文件第7页浏览型号110IMX7-05-05-8的Datasheet PDF文件第8页浏览型号110IMX7-05-05-8的Datasheet PDF文件第9页浏览型号110IMX7-05-05-8的Datasheet PDF文件第11页浏览型号110IMX7-05-05-8的Datasheet PDF文件第12页浏览型号110IMX7-05-05-8的Datasheet PDF文件第13页 
IMX7, IMS7 Series Data Sheet  
7-Watt DC-DC Converters  
Single-output models with R-input:  
100 to 105% Vo nom. Rext should be connected between pin  
4 and Vi. The following table indicates suitable resistor  
values for typical output voltages under nominal  
conditions (Vi nom, Io = 0.5 Io nom), with paralleled outputs or  
equal load conditions on each output.  
The R-input (pin 13) is referenced to the secondary side of the  
converter. Adjustment of the output voltage is possible by  
means of either an external resistor or a voltage source.  
Caution: Connection of Rext to Vi+ may damage the converter.  
06029e  
Vi+  
Vo+  
06089a  
Rext2  
Vi+  
Vo1+  
Vo1–  
Vo2+  
4 kΩ  
Vref = 2.5 V  
R
Trim  
+
+
Control  
logic  
+
Vext  
Rext1  
Control  
circuit  
Vref 2.5 V  
Vext  
Rext  
Vi–  
Vo–  
Vi–  
Vo2–  
Fig. 12  
Fig. 13  
Output voltage adjust for single-output models  
Output voltage adjust for double-output models  
a) Adjustment by means of an external resistor:  
Table 6: Rext for Vo > Vo nom  
approximate values (Vi nom, Io1 = Io2 = 0.5 Io1/2 nom  
Depending upon the value of the required output voltage,  
a resistor Rext1 or Rext2 shall be connected as shown in the  
figure below:  
Either: Rext1 between the R pin and Vo– to achieve an  
output voltage adjustment range of Vo = 75 to 100% of  
)
Vo [% Vo nom  
]
R
ext [k]  
105 to 108 (107 typically)  
0
105  
104  
103  
102  
101  
100  
1.5  
5.6  
12  
27  
68  
Vo nom (85 to 100% for 3.3 V outputs):  
Vo  
o nom Vo  
R
ext1 4 k• –––––––––  
V
or: Rext2 between the R pin and Vo+ to achieve an output  
voltage range of approximately Vo = 100 to 105% of Vo nom  
(V – 2.5 V)  
:
Note: Applying a control voltage greater than 20 V will set the  
converter into a hiccup mode.  
R
ext2 4 k• –––––o––––––––––––  
2.5 V • (Vo/Vo nom – 1)  
b) Adjustment by means of an external voltage Vext between  
Vo– and R pin.  
b) Adjustment by means of an external voltage source Vext  
.
For external output voltages in the range of 75 to 105% of  
Vo nom a voltage source Vext (0 to 20 V) is required,  
connected to the Trim-input (pin 4) and Vi–. The table  
below indicates typical Vo versus Vext values under  
nominal conditions (Vi nom, Io = 0.5 Io nom), with paralleled  
outputs or equal load conditions on each output. Direct  
paralleling of the Trim-inputs of converters connected in  
parallel is feasible.  
The control voltage is 1.96 to 2.62 V and allows for  
adjustment in the range of 75 to 105% of Vo nom  
.
Vo • 2.5 V  
V
ext ––––––––  
Vo nom  
Caution: Applying an external voltage >2.75 V may damage the  
converter.  
Note: Attempting to adjust the output below this range will cause  
the converter to shut down (hiccup mode).  
Table 7: Vext for Vo = 75 to 105% Vo nom  
;
typical values (Vi nom, Io1 = Io2 = 0.5 Io1/2 nom  
)
Double-output models with Trim input:  
Vo [% Vo nom  
]
Vext [V]  
The Trim input (pin 4) of double-output models is referenced to  
the primary side. Figure 13 shows the circuitry. Adjustment of  
the output voltage is possible in the range of 100 to 105% of V  
105  
102  
95  
0
1.6  
4.5  
9
o
nom using an external resistor, or in the range of 75 to 105% of  
85  
Vo nom using an external voltage source.  
75  
13  
a) Adjustment by means of an external resistor Rext  
.
Programming of the output voltage by means of an  
external resistor Rext1 is possible within a limited range of  
MELCHER  
The Power Partners.  
BCD20007-G Rev AF, 31-Jul-2015  
Page 10 of 14  

与110IMX7-05-05-8相关器件

型号 品牌 获取价格 描述 数据表
110IMX7-05-05-8G BEL

获取价格

DC-DC Regulated Power Supply Module, 2 Output, 7W, Hybrid, ROHS COMPLIANT PACKAGE-9
110IMX7-05-05-8M BEL

获取价格

DC-DC Regulated Power Supply Module, 2 Output, 7W, Hybrid
110IMX7-05-05-8ZG BEL

获取价格

DC-DC Regulated Power Supply Module, 2 Output, 7W, Hybrid, ROHS COMPLIANT PACKAGE-14
110IMX7-05-05-9 POWER-ONE

获取价格

7 Watt DC-DC Converters
110IMX7-05-05-9L BEL

获取价格

DC-DC Regulated Power Supply Module, 2 Output, 7W, Hybrid, 2 X 1 INCH, 10.50 MM HEIGHT, SM
110IMX7-05-05-9Z BEL

获取价格

暂无描述
110IMX7-05-7 BEL

获取价格

DC-DC Regulated Power Supply Module, 1 Output, 6.1W, Hybrid, 2 INCH X 1 INCH, 10.50 MM HEI
110IMX7-05-7D BEL

获取价格

DC-DC Regulated Power Supply Module, 1 Output, 6.1W, Hybrid, 2 INCH X 1 INCH, 10.50 MM HEI
110IMX7-05-7DM BEL

获取价格

DC-DC Regulated Power Supply Module, 1 Output, 6.1W, Hybrid, 2 INCH X 1 INCH, 10.50 MM HEI
110IMX7-05-7M BEL

获取价格

DC-DC Regulated Power Supply Module, 1 Output, 6.1W, Hybrid, 2 INCH X 1 INCH, 10.50 MM HEI