Datasheet > 09-06-2087

09-06-2087

更新时间： 2024-02-12 01:51:03

品牌	Logo	应用领域
莫仕 - MOLEX		/
页数	文件大小	规格书
6页	171K
描述
IDT CHANGE HEAD Specification Sheet

阅读下载

中文翻译

获取价格

技术参数
数据手册

如果您发现信息不准确，欢迎纠错

09-06-2087 技术参数

是否Rohs认证：	符合	生命周期：	Obsolete
Reach Compliance Code：	compliant	ECCN代码：	EAR99
HTS代码：	8536.69.40.40	风险等级：	5.76
其他特性：	POLARIZED	主体宽度：	0.37 inch
主体深度：	0.685 inch	主体长度：	1.266 inch
主体/外壳类型：	PLUG	连接器类型：	BOARD CONNECTOR
接触器设计：	PREASSEM CONN	联系完成配合：	NOT SPECIFIED
触点性别：	FEMALE	触点材料：	NOT SPECIFIED
触点模式：	RECTANGULAR	触点电阻：	20 m Ω
触点样式：	BELLOWED TYPE	DIN 符合性：	NO
介电耐压：	2000VAC V	耐用性：	25 Cycles
滤波功能：	NO	IEC 符合性：	NO
最大插入力：	8.896 N	最小绝缘直径：	0.045 inch
绝缘电阻：	200000000000 Ω	绝缘体颜色：	BLUE
绝缘体材料：	NYLON	MIL 符合性：	NO
插接触点节距：	0.156 inch	插接信息：	MULTIPLE MATING PARTS AVAILABLE
混合触点：	NO	安装选项1：	POLARIZED LCK
安装选项2：	PLASTIC	安装类型：	CABLE
装载的行数：	1	最高工作温度：	75 °C
最低工作温度：	-40 °C	选件：	GENERAL PURPOSE
极化密钥：	POLARIZED HOUSING	参考标准：	UL, CSA
可靠性：	COMMERCIAL	子类别：	Headers and Edge Type Connectors
端接类型：	IDC	触点总数：	8
UL 易燃性代码：	94V-2	最大线径：	20 AWG
最小线径：	20 AWG	撤离力-最小值：	2.224 N
Base Number Matches：	1

09-06-2087 数据手册

Change head for IDT Connectors Series

RIB OF CONNECTOR FACING UP

2. Place the proper connector into the track; the rib of the connector should be facing up. See

Figure 3.

3. Compress the front pistol handle and slide the connector into the Change Head track until it

stops, release the pistol handle.

4. Operate the pistol to index the connector into the change head.

5. Place the proper wire into the slot above the connector. Make sure that the wire is fully seated.

6. Close the piston hand tool by moving the front operating handle while holding the wire in place.

7. Release the operating handle gently. During the return stroke the housing will automatically

advance to the next circuit position.

8. Check for wire insulation depth in the location slot. The wire insulation must be just below the

“eagle” of the connector housing. See Figure 4.

9. Repeat steps 4 thru 7 above for placement of additional wires until the last circuit of the

housing is completed.

10. To remove the completed wire/housing assembly from the piston hand tool, slide the assembly

Figure 3

TRACK

to the right and push out.

Note: After the last wire insertion has been made in the connector assembly, the assembly will not advance any further because the

feed pawl will have cleared the end of the connector body.

EAGLE

ADJUSTMENTS

Wire Insertion Depth

1. Remove the Change Head from the pistol handle.

2. To adjust the insertion depth of the wire use the Allen wrench which is included with Change

Head.

3. Place the Allen wrench into the feed adjustment set screw, which is located in the mounting

slot of the change head that goes into the piston handle. See Figure 1.

4. By rotating this setscrew, the insertion depth can be changed.

5. Clockwise (CW) will increase wire insertion depth. Counter Clockwise (CCW) will decrease wire

WIRE

CONNECTOR

HOUSING

insertion depth.

Figure 4

Guide Plate

The two fixing screws on the front guide plate offer a small amount of track adjustment. This should only be adjusted if the connector

does not run smoothly through the track.

Connector Locator

The small slotted spring ball screw in the body molding of the change head is used to adjust the connector locator.

1. The spring ball screw should be loosened for 2,3,4, and 5 circuits size connector housings using a 3mm wide screwdriver blade.

See Figure 1.

2. For larger circuit size connector housing the spring ball screw should be tightened. This will ensure correct and consistent feed

action during operation.

This is set at the factory and should not require adjustment.

Doc No. 011215196

Revision: A

Release Date: 05-15-06

Revision Date: 05-15-06

UNCONTROLLED COPY

Page 5 of 6

1 2 3 456

中文翻译

下载PDF

与09-06-2087相关器件

型号	品牌	获取价格	描述	数据表
09-06-2088	MOLEX	获取价格	IDT CHANGE HEAD Specification Sheet
09-06-2089	MOLEX	获取价格	IDT CHANGE HEAD Specification Sheet
09-06-2090	MOLEX	获取价格	IDT CHANGE HEAD Specification Sheet
09-06-2097	MOLEX	获取价格	IDT CHANGE HEAD Specification Sheet
09-06-2098	MOLEX	获取价格	IDT CHANGE HEAD Specification Sheet
09-06-2099	MOLEX	获取价格	IDT CHANGE HEAD Specification Sheet
0906-2-10	COILCRAFT	获取价格	General Purpose Inductor, 0.0017uH, 10%, 1 Element, Air-Core, SMD
09-06-2100	MOLEX	获取价格	3.96mm (.156") KK® IDT Trifurcon™ Contact, 10
09-06-2107	MOLEX	获取价格	IDT CHANGE HEAD Specification Sheet
09-06-2108	MOLEX	获取价格	IDT CHANGE HEAD Specification Sheet

与09-06-2087相关文章

LM317T数据手册解读：产品特性、应用、封装与引脚详解
2024-06-14

4
一文带你了解?DB3二极管好坏判断、参数信息、替代推荐
2024-06-14

9
LM358DR数据手册：引脚说明、电气参数及替换型号推荐
2024-06-14

3
OP07CP数据手册解读：引脚信息、电子参数
2024-06-14

3

产品中心

服务支持

精选活动

关于我们

帮助中心

09-06-2087

09-06-2087 技术参数

09-06-2087 数据手册

与09-06-2087相关器件

与09-06-2087相关文章

您还可以找

产品中心

服务支持

精选活动

关于我们

帮助中心

09-06-2087

09-06-2087 技术参数

09-06-2087 数据手册

与09-06-2087相关器件

与09-06-2087相关文章

您还可以找

您在本页遇到什么问题？