Document 597-1
Z-Axis RFID Transponder Coils – ZXC
• Z-axis RFID coil can be used with any of our other RFID coils
for a complete three-dimensional solution.
• Only 10 mm square and 2.2 mm tall
• Four mounting pads for exceptional board adhesion
Core material Ferrite
Terminations RoHS matte tin over nickel over phos bronze. Other
terminations available at additional cost.
Weight 0.53–0.56 g
Ambient temperature –40°C to +125°C
Storage temperature Component: –40°C to +125°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Temperature Coefficient of Inductance ꢁTCLꢂ +25 to +200 ppm/°C
Moisture Sensitivity Level ꢁMSLꢂ 1 (unlimited floor life at <30°C /
85% relative humidity)
Mean Time Between Failures ꢁMTBFꢂ 26,315,789 hours
Packaging 500/7″ reel; 2000/13″ reel Plastic tape: 24 mm wide,
0.3 mm thick, 12 mm pocket spacing, 2.24 mm pocket depth
PCB washing Tested with pure water or alcohol only. For other solvents,
see Doc787_PCB_Washing.pdf.
Inductance2
at125kHz
5ꢀꢁmHꢂ
Read
Matching
distance3
ꢁinches/cmꢂ
Sensitivity4
ꢁmV/µTꢂ
capacitor5
ꢁpFꢂ
DCRmax6
ꢁOhmsꢂ
SRFtyp7
ꢁkHzꢂ
Partnumber1
Qmin2
ZXC-255XJL_
ZXC-495XJL_
ZXC-715XJL_
ZXC-116XJL_
ZXC-156XJL_
2.48
4.90
7.10
11.4
14.8
57
64
65
60
55
33/83.8
33/83.8
31/78.7
31/78.7
31/78.7
9.75
18.0
25.0
50.0
77.0
654
331
228
142
110
37
43
62
110
160
1975
1370
1220
990
815
1. When ordering, please specify packaging code:
ZXC-725XJLC
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (500 parts per full reel). Quantities less than full reel available: in tape (not
machine ready) or with leader and trailer ($25 charge).
D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (2000 parts per full reel).
B = Less than full reel. In an effort to simplify our part numbering system, Coilcraft is eliminating the need for multiple packaging codes.
When ordering, simply change the last letter of your part number from B to C.
2. Inductance and Q measured using Agilent/HP 4192A impedance analyzer at 125 kHz. For recommended test procedures, contact Coilcraft.
3. Read distance measured using the KEELOQ® Transponder Evaluation Kit part number DM303005 from Microchip. Distance was recorded as the volt-
age across the resonant circuit dropped below 10 mV.
4. Sensitivity measured in accordance with Coilcraft application note “Measuring Sensitivity of Transponder Coils.”
5. Matching capacitor value required for parallel resonant circuit operating at 125 kHz.
6. DCR measured on micro-ohmmeter.
7. SRF measured using Agilent/HP 8753D network analyzer.
8. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Document 597-1 Revised 03/24/10
US +1-847-639-6400 sales@coilcraft.com
UK +44-1236-730595 sales@coilcraft-europe.com
Taiwan +886-2-2264 3646 sales@coilcraft.com.tw
China +86-21-6218 8074 sales@coilcraft.com.cn
Singapore + 65-6484 8412 sales@coilcraft.com.sg
© Coilcraft Inc. 2021
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.