APPLICABLE STANDARD
USB2.0 SPECIFICATION AND MICRO-USB CABLES AND CONNECTORS SPECIFICATION.
STORAGE
OPERATING
-30C TO +85C
-30C TO +85C
TEMPERATURE RANGE
TEMPERATURE RANGE
SIGNAL ONLY
1.0 A/pin
RATING
1.8 A/pin (PIN No.1,No.5)
0.5 A/pin (PIN No.2-No.4)
CURRENT
VOLTAGE
AC 30V
POWER APPLY
SPECIFICATIONS
TEST METHOD
ITEM
REQUIREMENTS
QT AT
CONSTRUCTION
GENERAL EXAMINATION
VISUALLY AND BY MEASURING INSTRUMENT.
CONFIRMED VISUALLY.
ACCORDING TO DRAWING.
X
X
X
X
MARKING
ELECTRICAL CHARACTERISTICS
CONTACT RESISTANCE
INSULATION RESISTANCE
VOLTAGE PROOF
100 mA (DC OR 1000 Hz).
30 m MAX.
X
X
X
X
X
X
X
-
1000 M MIN.
500 V DC.
NO FLASHOVER OR BREAKDOWN.
2 pF MAX.
100 V AC FOR 1 min.
CAPACITANCE
MEASURE ADJACENT TWO CONTACTS AT
1000±10 Hz AC VOLTAGE.
MECHANICAL CHARACTERISTICS
INSERTION AND
A MAXIMUM RATE OF 12.5 mm/min
INSERTION FORCE
WITHDRAWAL FARCE
35 N MAX.
8 N MIN.
-
-
X
X
WITHDRAWAL FORCES
MEASURED BY APPLICABLE CONNECTOR
MECHANICAL OPERATION
10000 TIMES INSERTIONS AND EXTRACTIONS.
1) CONTACT RESISTANCE:
NO INCREASE OF MORE THAN 10 m
FROM INITIAL VALUE.
MATING SPEED
- MECHANICALLY OPERATED : 500 CYCLES / h.
2) INSERTION FORCE
WITHDRAWAL FORCE
35 N MAX.
8 N MIN.
- MANUALLY OPERATED
: 200 CYCLES / h
3) NO DAMAGE, CRACK AND LOOSENESS
OF PARTS.
VIBRATION
FREQUENCY 10 TO 55 Hz
1) NO ELECTRICAL DISCONTINUITY OF
X
X
X
SINGLE AMPLITUDE 0.75 mm, AT 2h
1s.
-
FOR 3 AXIAL DIRECTIONS. (6 HOURS IN TOTAL)
FREQUENCY 50 TO 2000 Hz AT 15 min
2) NO DAMAGE, CRACK AND LOOSENESS
OF PARTS.
RANDOM VIBRATION
SHOCK
FOR 3 AXIAL DIRECTIONS. (45 MINUTES IN TOTAL)
490 m/s2 DIRECTIONS OF PULSE 11 ms AT 3 TIMES FOR
-
-
6 DIRECTIONS. (18 TIMES IN TOTAL)
ENVIRONMENTAL CHARACTERISTICS
THERMAL SHOCK
TEMP –55 →+20 TO +35→+85→+20 TO + 35 C
TIME 30 → 5MAX 30 → 5MAX min
UNDER 10 CYCLES.
1) CONTACT RESISTANCE: 70 m MAX.
2) INSULATION RESISTANCE: 10 M MIN.
3) NO DAMAGE, CRACK AND LOOSENESS
OF PARTS.
X
X
→
-
-
(MATING APPLICABLE CONNECTOR)
HUMIDITY LIFE
TEMPERATURE -10~65 C, HUMIDITY 90 TO
98 , UNDER 7 CYCLES (168 h)
NO DAMAGE, CRACK AND LOOSENESS OF
PARTS.
(MATING APPLICABLE CONNECTOR)
DRY HEAT
NO DAMAGE, CRACK AND LOOSENESS OF
PARTS.
EXPOSED AT 85±2 C, 96 h.
(MATING APPLICABLE CONNECTOR)
X
X
-
-
COLD
NO DAMAGE, CRACK AND LOOSENESS OF
PARTS.
EXPOSED AT -40±2 C, 96 h.
(MATING APPLICABLE CONNECTOR)
CORROSION SALT MIST
SOLDERABILITY
NO HEAVY CORROSION.
EXPOSED AT 5 % SALT WATER, 35 C, FOR 48h.
(LEFT UNDER UNMATED CONDITION)
SOLDERING POINT IMMERSED IN SOLDER BATH OF
255±5℃,5 sec. (USING TYPE R FLAX)
X
X
-
-
SOLDER SHALL COVER MINIMUM OF 95% OF
THE SURFACE BEING IMMERSED
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
CHECKED
DATE
0
△
REMARK
APPROVED
CHECKED
DESIGNED
NM.NISHIMATSU
KN.ICHIKAWA
TS.ITO
15.10.27
15.10.27
15.10.27
HIROSE will not guarantee the performance on these specifications in
case this product will be mated with the others which is not
HIROSE’s.
DRAWN
AK.AKIYAMA
15.10.27
Unless otherwise specified, refer to USB2.0, EIA364 or IEC 60512.
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
DRAWING NO.
ELC-126701-30-00
PART NO.
CODE NO.
ZX62MD2-B-5PA(30)
CL242-0050-7-30
SPECIFICATION SHEET
HIROSE ELECTRIC CO., LTD.
0
△
1/2
FORM HD0011-2-1