APPLICABLE STANDARD
USB3.0 SPECIFICATION AND MICRO-USB CABLE AND CONNECTORS SPECIFICATION.
STORAGE
OPERATING
-30C TO +85C
-30C TO +60C
TEMPERATURE RANGE
TEMPERATURE RANGE
SIGNAL ONLY
1.0 A/pin
RATING
VOLTAGE
30V AC
CURRENT
POWER APPLY 1.8 A/pin (PIN No.1,No.5)
0.5 A/pin(PIN No.2 TO 4,No.6 TO 10)
SPECIFICATIONS
TEST METHOD
ITEM
REQUIREMENTS
QT AT
CONSTRUCTION
GENERAL EXAMINATION
VISUALLY AND BY MEASURING INSTRUMENT.
CONFIRMED VISUALLY.
ACCORDING TO DRAWING.
X
X
X
X
MARKING
ELECTRIC CHARACTERISTICS
30 m MAX.
CONTACT RESISTANCE
INSULATION RESISTANCE
VOLTAGE PROOF
100 mA (DC OR 1000 Hz).
X
X
X
X
X
X
X
-
500 V DC.
1000 M MIN.
100 V AC FOR 1 min.
NO FLASHOVER OR BREAKDOWN.
2 pF MAX.
CAPACITANCE
MEASURE ADJACENT TWO CONTACTS AT
1000±10Hz AC VOLTAGE.
MECHANICAL CHARACTERISTICS
INSERTION FORCE
35 N MAX.
INSERTION AND
A MAXIMUM RATE OF 12.5 mm/min
-
-
X
X
WITHDRAWAL FARCE 10 N MIN.(INITIAL)
WITHDRAWAL FORCES
MEASURED BY APPLICABLE CONNECTOR
MECHANICAL OPERATION
10000 TIMES INSERTIONS AND EXTRACTIONS.
1) CONTACT RESISTANCE:
NO INCREASE OF MORE THAN 10 m
FROM INITIAL VALUE.
MATING SPEED
- MECHANICALLY OPERATED : 500 CYCLES / h
2) INSERTION FORCE
WITHDRAWAL FORCE
35 N MAX.
8 N MIN.
or
- MANUALLY OPERATED
: 200 CYCLES / h
3) NO DAMAGE, CRACK AND LOOSENESS
OF PARTS.
VIBRATION
FREQUENCY 10 TO 55 Hz
1) NO ELECTRICAL DISCONTINUITY OF
X
X
X
SINGLE AMPLITUDE 0.75 mm, AT 2h
1s.
-
(6 HOURS IN TOTAL) FOR 3 AXIAL DIRECTIONS.
FREQUENCY 50 TO 2000 Hz AT 15 min
2) NO DAMAGE, CRACK AND LOOSENESS
OF PARTS.
RANDOM VIBRATION
SHOCK
(45 MINUTES IN TOTAL) FOR 3 AXIAL DIRECTIONS.
490 m/s2 DURATION OF PULSE 11 ms AT 3 TIMES IN 3
-
-
BOTH AXIAL DIRECTIONS.
ENVIRONMENTAL CHARACTERISTICS
THERMAL SHOCK
TEMP –55 →+15 TO +35→+85→+15 TO+ 35 C
TIME 30 → 2 TO 3 30→ 2 TO 3 min.
UNDER 10 CYCLES.
1) CONTACT RESISTANCE: 70 m MAX.
2) INSULATION RESISTANCE: 10 M MIN.
3) NO DAMAGE, CRACK AND LOOSENESS
OF PARTS.
X
X
→
-
-
(MATING APPLICABLE CONNECTOR)
TEMPERATURE -10 TO 65 C, HUMIDITY 93±3 ,
UNDER 7 CYCLES (168 h)
HUMIDITY LIFE
NO DAMAGE, CRACK AND LOOSENESS OF
PARTS.
(MATING APPLICABLE CONNECTOR)
DRY HEAT
EXPOSED AT 85C±2C, 96 h.
(MATING APPLICABLE CONNECTOR)
NO DAMAGE, CRACK AND LOOSENESS OF
PARTS.
X
X
-
-
COLD
EXPOSED AT -40C±3C, 96 h.
(MATING APPLICABLE CONNECTOR)
NO DAMAGE, CRACK AND LOOSENESS OF
PARTS.
CORROSION SALT MIST
SOLDERBILITY
EXPOSED AT 5 % SALT WATER, 35 C, FOR 48h.
(LEFT UNDER UNMATED CONDITION.)
SOLERRING POINT OF CONTACTS IMMERSION IN
SOLDER BATH OF 255C±2C, 5 sec.
NO HEAVY CORROSION.
X
X
X
-
-
-
SOLDERING POINT OF CONTACTS
IMMERSION IN SOLDER 95% MIN.
NO DEFORMATION OR SIGNIFICANT
LOOSENESS OF CONTACTS.
RESISTANCE TO
SOLDERING HEAT
A PROFILE IS SHOWN IN FIG-1, UNDER 2 CYCLES.
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
CHECKED
DATE
△0
REMARK
APPROVED
CHECKED
DESIGNED
DRAWN
NM.NISHIMATSU
KN.ICHIKAWA
TS.ITO
15.10.27
15.10.27
15.10.27
15.10.27
HIROSE will not guarantee the performance on these specifications in
case this product will be mated with the others which is not
HIROSE’s.
AK.AKIYAMA
Unless otherwise specified, refer to USB3.0, EIA364 or IEC 60512.
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
DRAWING NO.
ELC-128027-30-00
PART NO.
CODE NO.
ZX360D1-B-10P(30)
CL242-0513-3-30
SPECIFICATION SHEET
HIROSE ELECTRIC CO., LTD.
0
△
1/2
FORM HD0011-2-1