Document 1270B-1
LowProfileUSBCommonModeChoke ZE2401-AE
• Common mode choke suitable for use in FPD-Link III & FPD-
Link IV up to 13.5 Gbps link rates
• Attenuate common mode signal with minimal effect on
differential signal in forward channel and backchannel for
maintaining stable signal integrity
Core material Ferrite
Environmental RoHS compliant
Terminations Matte tin over nickel over silver-palladium-glass frit.
Weight 14.7 – 15.5 mg
Ambient temperature –40°C to +125°C with Irms current.
Maximum part temperature 140°C
Storage temperature Component: –40°C to +140°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Packaging 2000/7″ reel; 7500/13″ reel; Plastic tape: 8 mm wide,
0.23 mm thick, 4 mm pocket spacing, 1.295 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Common mode
Common mode
Cutoff
DCR
max4
(Ohms)
attenuation typ (dB)
peak impedance frequency2
Inductance3
min (nH)
Isolation5 Irms6
(Vrms) (mA)
Part number1
(kOhms)
(GHz)
10 MHz 100 MHz 500 MHz
ZE2401-AE_
>0.16@>3.0 GHz
>5.0
1.5
5.3
7.1
30
0.35
250
100
0.080 0.004
2,03 0,10
1. When ordering, please specify packaging code:
ZE2401-AEC
1
2
Packaging:C= 7″ machine-ready reel. EIA-481 embossed plastic
tape (2000 parts per full reel). Quantities less than
full reel available: in tape (not machine ready) or
with leader and trailer ($25 charge).
0.055
max
1,40
4
3
0.004
0,10
D= 13″ machine-ready reel. EIA-481 embossed plas-
tic tape (7500 parts per full reel).
0.040
1,02
0.030 0.036
0.020
0,51
2 Frequency at which the differential mode attenuation equals −3 dB
3. Inductance measured at 100 MHz using an Agilent/HP 4286A
impedance analyzer and a Coilcraft SMD-A fixture.
0.018
0,46
0,76
0,91
0.014
0,36
2
1
4
1
4
2
4. DCR is specified per winding.
0.050 0.004
1,27 0,10
5. Winding to winding isolation (hipot) tested for one minute.
6. Current per winding that causes a 15°C rise from 25°C ambient.
7. Electrical specifications at 25°C.
3
3
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
inches
mm
0.020
0,51
Recommended
Land Pattern
Dimensions are in
US +1-847-639-6400 sales@coilcraft.com
Document 1270B-1 Revised 08/23/23
UK +44-1236-730595 sales@coilcraft-europe.com
Taiwan +886-2-2264 3646 sales@coilcraft.com.tw
China +86-21-6218 8074 sales@coilcraft.com.cn
Singapore + 65-6484 8412 sales@coilcraft.com.sg
© Coilcraft Inc. 2023
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.