EXSTOR - 1 XRS10L240
SERIAL ATA II: PORT MULTIPLIER / PORT SELECTOR
REV. 1.05
JANUARY 2009
FEATURES
independent hosts, the XRS10L240 offers a leading
solution for propagation of high data rate Serial ATA
products in a wide variety of applications. The
integration of Serial ATA PHY links, a variety of digital
logic capabilities, rate adjust FIFOs, integrated low-
cost clock oscillator support, test and loopback
features is achieved in a low cost and lower power
implementation.
G
•
ENERAL FEATURES
Six independent 3/1.5Gbps SATA ports.
Connects 2 host ports to 4 device ports.
•
•
Supports 3/1.5Gbps rate detection/speed
negotiation.
The port selector function is used when dual hosts,
such as I/O controllers, must access single-port disk
drives in high availability storage subsystems where
redundancy and load sharing are important. The
outputs from the I/O controllers are multiplexed to a
Serial ATA drive through the port selector block of the
XRS10L240. Active/passive port selector in
XRS10L240 allows two different host ports to connect
to the same target in order to create a redundant path
to that target. In combination with RAID, the
XRS10L240 allows system providers to build fully
redundant solutions. This avoids the presence of a
single point of failure, and enables a fail-over path in
the case of host failure.
•
•
Supports power down modes - Active, partial,
slumber and power down.
Advanced features configurable through MDIO
bus.
P
ORT MULTIPLIER/SELECTOR LOGIC FEATURES
•
Low latency architecture.
•
Supports OOB signaling for SATA applications.
Internal OOB detectors for COMRESET/
COMINIT and COMWAKE.
I/O FEATURES
•
High speed outputs with programmable pre-
emphasis to drive long interconnects.
This port multiplier function is used when one active
host has to communicate with multiple SATA drives.
The XRS10L240 supports up to 4 SATA drives and
utilizes the full bandwidth of the host connection.
•
•
•
Selectable high speed input equalization for
optimum reception.
Compliant with SATA Gen-2i
specification.
&
Gen-2m
The XRS10L240 includes enhanced features such as
staggered HDD spin-up, power management control,
hot plug capability and support for legacy software.
Enables reliable data transmission over 1 meter
or more of FR-4 and 4 meters or more of The XRS10L240 acts as a retimer, maintaining
unequalized copper cable.
independent signaling domains between the drives,
hosts and the external interconnect.
•
Selectable spread spectrum clocking (SSC) to
reduce EMI.
The high-speed serial input feature: selectable
equalization and the high-speed serial output feature:
programmalbe pre-emphasis can be used to
compensate for ISI (Inter-Symbol Interference) and
increase maximum cabling distances.
P
•
•
•
•
•
HYSICAL FEATURES
CMOS 0.13 Micron Technology
Single 1.2 V Power Supply
XRS10L240 meets tight jitter budgets in SATA
applications. Exar's serial I/O technology enables
reliable data transmission over 1 meter or more of
FR-4 and 4 meters or more of unequalized copper
cable.
-40°C to 85°C Industrial Temperature Range
No heatsink or airflow required
100-Pin LQFP Package
Host and drive port speeds can be mixed and
matched, based upon inherent data rate negotiation
present in the SATA II specifications.
1.0 INTRODUCTION
The XRS10L240 provides the combined advantages
of the Serial ATA II Port Selector and Port Multiplier
implementations for Serial ATA II systems at 3.0
Gbps and 1.5 Gbps. Combining the capability to
address four Serial ATA devices from one external
link with support for a failover path from two
The MDIO bus allows simple configuration of the
XRS10L240 when needed. Receive equalization,
transmit amplitude and pre-emphasis and SSC
control are all configurable via the 2-wire MDIO
interface.
Exar Corporation 48720 Kato Road, Fremont CA, 94538 • (510) 668-7000 • FAX (510) 668-7017 • www.exar.com