THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
HTTP://WWW.CONWIN.COM
P R O D UC T D ATA S H E E T
CRYSTAL CONTROLLED OSCILLATORS
CW 0701
VSPLD53TED1
622.08M
3.3V SURFACE MOUNT LVPECL VCSO OSCILLATOR
with SELECTABLE OUTPUT FREQUENCY
ABSOLUTE MAXIMUM RATINGS
TABLE 1.0
VSPLD53TED1
PARAMETER
UNITS
MINIMUM NOMINAL MAXIMUM
UNITS
°C
NOTE
Storage Temperature
Supply Voltage
-55
-0.5
-0.5
-
-
-
125
7.0
7.0
(Vcc)
(Vc)
Vdc
Vdc
DESCRIPTION
Control Voltage
OPERATING SPECIFICATIONS
PARAMETER
TABLE 2.0
NOTE
The Connor-Winfield
VSPLD53TED1 is a Dual
Frequency, 3.3V Voltage
Controlled SAW Oscillator
MINIMUM NOMINAL MAXIMUM
UNITS
MHz
-
-
-
-
Center Frequency: Frequency Select @ “0”
Center Frequency: Frequency Select @ “1”
Total Frequency Tolerance
(Fo)
(Fo)
622.0800
669.3265
MHz
-80
-
-
80
70
3.465
80
3.0
0.5
-
ppm
1
(VCSO) with Differential LVPECL
outputs. The output frequency
622.08MHz or 669.3265MHz is
selectable by applying logic “0” or
logic “1” to the FS pad (Pad 2).
The VSPLD53TED1 is designed
for use with PLL systems in
SONET/SDH systems requiring
low jitter and tight stability. No
multiplication schemes are used
in this oscillator design.
Operating Temperature Range
Supply Voltage
0
°C
(Vcc)
(Icc)
3.135
3.3
-
Vdc
Supply Current
-
-
-
-
-
-
-
mA
Jitter (BW=10Hz to 20MHz)
Jitter (BW=12kHz to 80MHz)
SSB Phase Noise at 100Hz offset
SSB Phase Noise at 1KHz offset
SSB Phase Noise at 10KHz offset
SSB Phase Noise at 100KHz offset
-
ps rms
ps rms
dBc/Hz
dBc/Hz
dBc/Hz
dBc/Hz
-
-70
-105
-145
-155
-
-
-
INPUT CHARACTERISTICS
PARAMETER
TABLE 3.0
NOTE
MINIMUM NOMINAL MAXIMUM
UNITS
Vdc
ppm
%
Control Voltage Range
(Vc)
0.3
1.65
3.0
Absolute Pull Range (APR)
Monotonic Linearity
+/-30
-
-
2
FEATURES
-10
-
10
Input Impedance
-
50K
-
Ohm
KHz
Vdc
Vdc
-
-
Modulation Bandwidth (3dB)
Frequency “0” Select Voltage (Low)
Frequency “1” Select Voltage (High)
10
-
SELECTABLE OUTPUT FREQUENCY:
622.08MHz or 669.3265MHz
“0”
“1”
-
<30% Vcc
-
-
>70% Vcc
LOW PROFILE, SURFACE MOUNT
PACKAGE
LOW VOLTAGE PECL OUTPUT CHARACTERISTICS
TABLE 4.0
NOTE
3
PARAMETER
MINIMUM NOMINAL MAXIMUM
UNITS
Ohms
Vdc
Vdc
%
3.3V OPERATION
LOAD
-
-
-
50
-
Voltage
(High)
(Low)
(Voh)
(Vol)
2.275
LOW JITTER <0.5pS RMS
-
45
-
-
1.68
55
Duty Cycle at 50% Level
50
250
FREQUENCY TOLERANCE: ±80ppm
TEMPERATURE RANGE: 0 to 70°C
DIFFERENTIAL LVPECLOUTPUTS
TAPEAND REEL PACKAGING
Rise / Fall Time 20% to 80%
400
pS
PACKAGE CHARACTERISTICS
TABLE 5.0
Package
Non-hermetic package consisting of an FR4 substrate with grounded metal
cover.
PROCESS RECOMMENDATIONS
Solder Reflow
TABLE 6.0
The component solder used internal to this device has a m elting point of
221°C. The peak temperature inside the device should be less than or equal
to 220°C for a maximum of 10 seconds
ORDERING INFORMATION
Wash
Notes
Ultrasonic cleaning is not recommended.
VSPLD53TED1 - 622.08MHz
1.0
Inclusive of calibration @ 25°C, frequency stability vs. temperature, supply and load variations, shock, vibration and aging
for ten years. Control voltage (Vc) = 1.65 Vdc.
Control voltage for (Fo) = 1.65 Vdc Typical. Positive Transfer Func tion.
50 ohm termination into Vcc-2V or Thevein equivalent.
VCSO
SERIES
CENTER
FREQUENCY
2.0
3.0
Specifications subject to change without notice.
8/25/04
Vs008
1
2
00
REV:
Copyright 2001 Connor-Winfield all rights reserved.
DATASHEET #:
PAGE
OF
DATE:
a