VF1 6 0 / 1 6 1 E
X O
VF160–E/VF161–E
10KH ECL/PECL Compatible
Enable/Disable Clock Oscillator
F E AT U R E S
Pa ra m e te r
Sy m b
Co n d itio n
Min
Ty p
Ma x
Un it
N o te
• Enable/Disable Output
Input Break
Down Voltage
Vcc–Vee
–0.5
7.0
V
• Industrial Temperature Range
Storage Temp.
Ts
F
–40
10
+85
300
°C
• In–house “Inverted Mesa” Crystal
Frequency
Range
MHz
Technology for Higher Frequencies
• Wide Frequency Range
Frequency
Stability
∆F/ F
Overall Conditions
Including:
Calibration, temp.,
aging 10 yrs.
shock, vibration
±100
ppm
1
• Very Low Phase Jitter
Input Voltage
Vcc
Vcc
Vee
PECL
LVPECL
ECL
4.75
3.15
–4.95
5.00
3.30
–5.20
5.25
3.45
–5.45
V
VF161E
VF161L–E
VF160E
VALPEYFISHER
0.497"
VF161-E
200MHZ
BO1H
(12,62mm)
Input Current
Load
Icc/ Iee
50 Ohm Load
80
mA
50 Ohm to Vcc–2V or Thevenin Equiv. Bias required
0.800"
(20,32mm)
Duty Cycle
Rise/ Fall Time
Logic “1” Level
@50%
45
50
55
%
ns
V
2
Tr/ Tf
Voh
20% to 80%
1.5
0.187"
(4,75mm)
@Vcc = 5.0V
@Vee = –5.2V –0.96
@Vcc = 3.3V
4.04
4.19
–0.81
2.74
PECL
ECL
LVPECL
2.59
0.250"
(6,35mm)
ø0.0180"
(0,460mm)
Logic “0” Level
Vol
Ts
@Vcc = 5.0V
@Vee = –5.2V –1.85
@Vcc = 3.3V
3.15
3.25
–1.65
1.55
V
PECL
ECL
LVPECL
1.45
GLASS STANDOFFS
#1
Start–up Time
Phase Jitter
2
10
1
ms
ps
#7
1σ
fj>1KHz
Control input “Vee” or floating
Control input “High”
– Enable
– Disable Low
0.300"
(7,62mm)
Enable/
Disable Function
Operating
Temperature Range
#14
#9
#8
0°C to +70°C (–40°C to +85°C available)
Per MIL–STD–202, Method 213, Cond. E
Per MIL–STD–883, Method 1011, Cond. A
Per MIL–STD–883, Method 2007, Cond. A
260°C, for 10s, Max.
0.100"
(2,54mm)
0.600"
(15,24mm)
Mechanical Shock
Thermal Shock
Vibration
All dimensions are typical unless otherwise specified.
Soldering Conditions
Hermetic Seal
Pin Out
Creating a Part Number
Leak rate less than 5 x 10–8 atm.cc/ s of helium
FREQ.
E
VF160/161
Pin #1–Enable/ Disable Control
Pin #7–Ground, Case (PECL)/ Vee (ECL)
Pin #8–Output
Pin #9–Optional – Complementary output
Pin #14–Vcc (PECL)/ Ground, Case (ECL)
LEAD CONFIGURATION
FREQUENCY STABILITY
Code
G
Specification
Gull Wing
Through Hole (std.)
Code
Specification
S
A
B
±20
±25
±50
ppm
ppm
ppm
OUTPUT
±100 ppm (std.)
Code
C
Specification
Complementary
Single output (std.)
DUTY CYCLE
Notes:
Code
HH
Specification
±2.5%
1. Standard frequency stability (±20, ±25, ±50, others available).
2. Tighter duty cycles available. Measure @ 50% of the voltage swing.
3. Pin #9 omitted if complementary output is not specified.
OPERATIONAL TEMP. RANGE
±5%
Code
1
Specification
0°C to +70°C (std.)
-40°C to +85°C
INPUT VOLTAGE
All specifications are subject to change without notice.
Code
L
Specification
3.3 Volt ±5%
5.0 Volt ±5% (std.)
Example: VF161SHHL-1CE-200MHz: Frequency Stability ±20ppm, Duty Cycle
±2.5%, Input Voltage 3.3 Volt ±5%, Operating Temperature -40°C to +85°C,
Complementary Output, Enable/Disable, Frequency 200.000MHz.
57
75 South Street, Hopkinton, MA 01748 800-982-5737 508-435-6831 Fax: 508-435-5289 www.valpeyfisher.com