ALUMINUM ELECTROLYTIC CAPACITORS
6mmL Chip Type, Bi-Polarized
UUP
Chip type, bi-polarized withstanding high temperature range up to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
Extended
UUN
UUP
range
High
Temperature
UWP
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
Rated Capacitance Range
Capacitance Tolerance
Leakage Current
–55 to +105°C
6.3 to 50V
0.1 to 47µF
20% at 120Hz, 20°C
After 2 minutes' application of rated voltage at 20°C, leakage current is not more than 0.05 CV or 10 (µA), whichever is greater.
Measurement frequency : 120Hz at 20°C
Rated voltage (V)
6.3
10
16
25
35
50
Tangent of loss angle (tan δ)
tan δ (MAX.)
0.24
0.20
0.17
0.17
0.15
0.15
Measurement frequency : 120Hz
Rated voltage (V)
6.3
4
8
10
3
6
16
2
4
25
2
4
35
2
3
50
2
3
Stability at Low Temperature
Z–25°C / Z+20°C
Z–40°C / Z+20°C
Impedance ratio
ZT / Z20 (MAX.)
The specifications listed at right shall be met
when the capacitors are restored to 20°C after
the rated voltage is applied for 1000 hours at
105°C with the polarity every 250 hours.
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
Capacitance change
tan δ
Within 20% of the initial capacitance value
200% or less than the initial specified value
Less than or equal to the initial specified value
Endurance
Shelf Life
Leakage current
The capacitors are kept on a hot plate for 30 seconds, which is
Capacitance change
tan δ
Within 10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Resistance to soldering
heat
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate
and restored to 20°C.
Leakage current
Marking
Black print on the case top.
Chip Type
Type numbering system (Example : 16V 10 F)
µ
1
2
3
4
5
6
7
8
9 10 11 12 13 14
105˚C Marking
Capacitance
U U P 1 C 1 0 0 M C L 1 G S
Plastic platform
C
0.2
0.3 MAX.
Voltage
Lot No.
Taping code
(mm)
6.3
Configuration
φD
4
5
Capacitance tolerance ( 20%)
Rated capacitance (10µF)
Rated voltage (16V)
Series name
A
B
C
E
1.8 2.1 2.4
4.3 5.3 6.6
4.3 5.3 6.6
1.0 1.3 2.2
0.5 to 0.8
5.8 0.3
Type
Voltage mark for 6.3V is 6V
Dimensions
6.3
10
16
25
35
50
V
Cap.(µF)
Code
0J
1A
1C
1E
1V
1H
0.1
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
4
4
4
4
4
5
5
6.3
1.0
2.0
2.8
4.0
8.4
13
17
20
0.22
0.33
0.47
1
2.2
3.3
4.7
4
5
5
6.3
8.4
16
18
29
5
5
6.3
12
16
27
4
5
6.3
6.3
12
10
4
6.3
6.3
17
33
41
23
37
49
22
33
47
5
6.3
6.3
28
37
45
Rated
ripple
Case size
φ D(mm)
Rated ripple current (mArms) at 105°C 120Hz
Frequency coefficient of rated ripple current
Taping specifications are given in page 23.
Frequency
50 Hz
120 Hz
300 Hz
1 kHz
10 kHz or more
Recommended land size, soldering by reflow are given in page 18, 19.
Please select UUN(p.164) if high CV products are required.
Please refer to page 3 for the minimum order quantity.
Coefficient
0.70
1.00
1.17
1.36
1.50ꢀꢀ
122
5秒后页面跳转
MAX7219驱动8段数码管详解及数据手册关键信息
ATMEGA328P技术资料深入分析
AT24C02芯片手册管脚信息、参数分析、应用领域详解
AT24C256芯片手册参数分析、引脚说明、读写程序示例
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
