ALUMINUM ELECTROLYTIC CAPACITORS
Chip Type, High Reliability
UUB
(Through 50V only)
Chip type, high temperature range, for +125°C use.
Applicable to automatic mounting machine
fed with carrier tape.
ULT
UWH
High
Temperature
Reflow
High
Voltage
Compliant to the RoHS directive (2011/65/EU).
Added ESR specification
at 40°C
High
Temperature
UCJ
UUX
–
UUB
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
–40 to +125°C
10 to 400V
Rated Capacitance Range
Capacitance Tolerance
1 to 330µF
20% at 120Hz, 20°C
Rated voltage (V)
Leakage Current
10 to 50
160 to 400
Leakage Current
After 1 minute's application of rated voltage at 20°C, leakage current is not more than 0.03CV (µA).
Measurement frequency : 120Hz at 20°C
I = 0.04CV+100(µA) max.(1 minute's at 20°C)
Rated voltage (V)
10
16
25
35
50
160
200
250
400
Tangent of loss angle (tan δ)
0.32
0.24
0.21
0.18
0.18
0.30
0.30
0.30
0.30
tan δ (MAX.)
Measurement frequency : 120Hz
Rated voltage (V)
Impedance ratio
ZT / Z20 (MAX.)
10
12
16
25
6
35
4
50
4
160
8
200
8
250
8
400
12
Stability at Low Temperature
Z–40°C / Z+20°C
8
Capacitance change
tan δ
Leakage current
Within 30% of the initial capacitance value
300% or less than the intial specified value
Less than or equal to the initial specified value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours (1000 hours for φ8 × 6.2) at 125°C.
Endurance
Shelf Life
After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds,
Capacitance change
tan δ
Leakage current
Within 10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
Resistance to soldering
heat
which is maintained at 250°C. The capacitors shall meet
the characteristic requirements listed at right when they
are removed from the plate and restored to 20°C.
Marking
Black print on the case top.
Chip Type
Type numbering system (Example : 10V 100 F)
µ
1
2
3
4
5
6
7
8
9 10 11 12 13 14
Positive
(φ8 × 6.2)
125˚C Marking
Plastic platform
U U B 1 A 1 0 1 M C L 1 G S
C
0.2
0.3MAX.
Voltage
Capacitance
Lot No.
Taping code
Configuration
D × L Code
Trade mark
φ
Capacitance tolerance ( 20ꢀ%
8 × 6.2
CL
NL
NL
Rated capacitance
(
100µF
%
%
L
0.3
H
8 × 10
Negative
Positive
Rated voltage
(10V
10 × 10
(φ8 × 10, φ10)
Series name
Type
Plastic platform
0.3MAX.
125˚C Marking
Lot No.
Trade mark
C
0.2
Capacitance
Voltage
(mm%
10 × 10
3.2
10.3
10.3
4.5
φD × L
8 × 6.2
3.3
8 × 10
2.9
8.3
8.3
3.1
10
A
B
C
E
L
8.3
8.3
2.3
6.2
H
L
0.5
10
Negative
H
0.5 to 0.8 0.8 to 1.1 0.8 to 1.1
Pressure relief vent
Dimensions
V
10
1A
16
1C
25
1E
35
1V
50
1H
Cap.(µF)
010
Code
100
220
330
470
101
221
331
8 × 6.2
8 × 6.2
8 × 10
24
38
46
58
022
033
8 × 6.2
8 × 10
10 × 10
44
52
80
047
8 × 6.2
8 × 10
10 × 10
48
74
116
10 × 10
100
8 × 6.2
8 × 10
10 × 10
58
8 × 10
10 × 10
66
102
Case size
Rated
ripple
220
90
φ D × L (mm)
330
112
V
160
2C
200
2D
250
2E
400
Cap.(µF)
Code
010
2G
1
8× 10
26
27
36
38
Frequency coefficient of rated ripple current
1.8
1R8
2R2
3R3
4R7
6R8
100
8× 10
10× 10
10× 10
Frequency
50 Hz
120 Hz 300 Hz
1 kHz 10 kHz or more
2.2
3.3
4.7
6.8
10
Coefficient
0.70
1.00 1.17
1.36
1.50
8× 10
10× 10
28
59
8× 10
10× 10
10× 10
36
59
59
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given in
page 18, 19.
8× 10
10× 10
42
59
Case size Rated
ripple
φ D × L (mm)
Please refer to page 3 for the minimum order quantity.
Rated ripple current (mArms) at 125°C 120Hz
145