NEC's GENERAL PURPOSE
5 V AGC AMPLIFIER
UPC3217GV
UPC3218GV
VOLTAGE GAIN vs.
FEATURES
AUTOMATIC GAIN CONTROL VOLTAGE*
60
T
V
A
= +25ºC
CC = 5V
f = 45 MHz
in = -50 dBm
•
•
•
•
•
ON-CHIP LOW DISTORTION AMPLIFIER:
IIP3 = -4 dBm at minimuim gain
50
40
30
20
10
0
P
Z
L
= 250Ω
WIDE AGC DYNAMIC RANGE:
GCR = 53 dB TYP
ON-CHIP VIDEO AMPLIFIER:
VOUT = 1.25 VP-P at single-ended output
UPC3217GV
SUPPLY VOLTAGE:
VCC = 5 V
-10
PACKAGED IN 8 PIN SSOP SUITABLE FOR
SURFACE MOUNTING
0
1
2
3
4
5
Automatic Gain Control Voltage, VAGC* (V)
DESCRIPTION
70
T
V
A
= +25ºC
CC = 5V
f = 45 MHz
in = -60 dBm
60
50
40
30
20
10
NEC's UPC3217GV and UPC3218GV are Silicon Monolithic
ICs designed for use as AGC amplifiers for digital CATV,
cablemodemsandIPtelephonysystems. TheseICsconsist
of a two stage gain control amplifier and a fixed video gain
amplifier. The devices provide a differential input and differ-
ential output for noise performance, which eliminates shield-
ing requirements.
P
Z
L
= 250Ω
UPC3218GV
The package is 8-pin SSOP (Shrink Small Outline Package)
suitable for surface mount.
0
0
1
2
3
4
5
These ICs are manufactured using NEC's 10 GHz fT
NESATΙΙ AL silicon bipolar process. This process uses
silicon nitride passivation film. This material can protect chip
surface from external pollution and prevent corrosion/migra-
tion. Thus, theseICshaveexcellentperformance, uniformity
and reliability.
Automatic Gain Control Voltage, VAGC* (V)
APPLICATIONS
•
•
•
Digital CATV
NEC's stringent quality assurance and test procedures en-
sure the highest reliability and performance.
Cable modem receivers
IP Telephony Receivers
ELECTRICAL CHARACTERISTICS
(TA = 25°C, VCC = 5 V, ZS = 1 K Ω, ZL = 240 Ω, fIN = 45 MHz, Unless otherwise specified)
PART NUMBER
PACKAGE OUTLINE
UPC3217GV
S08
UPC3218GV
S08
SYMBOLS
PARAMETERS AND CONDITIONS
UNITS
MIN
TYP
MAX
MIN
TYP
MAX
DC Characteristics
ICC
Circuit Current (no input signal)
mA
15
23
34
15
23
34
RF Characterisitics
BW
GMAX
GMIN
GCR
NFAGC
VOUT
IM3
Frequency Bandwidth, VAGC* = 4.5 V1
Maximum Gain , VAGC* = 4.5 V
Minimum Gain, VAGC* = 0.5 V
Gain ConTrol Range, VAGC* = 0.5 to 4.5 V
Noise Figure, VAGC* = 4.5 V at MAX Gain
Output Voltage, Single Ended Output
Third Order Intermodulation Distortion,
fIN1 = 44 MHz, fIN2 = 45 MHz,
MHz
dB
dB
100
53
0
100
63
10
50
-4.5
46.5
56
3.5
60
4.5
46.5
66
13.5
dB
53
53
dB
VP-P
dBc
6.5
1.25
55
8.0
3.5
1.25
55
4.5
VIN = 30 dBmV per tone2
Note:
1. -3dB with respect to 10 MHz gain
2. VAGC is adjusted to establish VOUT = 1.25 VP-P per tone
California Eastern Laboratories
* VAGC shown as applied in the evaluation cicuit (see page 5) through a resistive bridge (voltage divider).
Actual voltage range on the pin of the IC is 0 to 3 V.