ALUMINUM ELECTROLYTIC CAPACITORS
Chip Type, High Voltage.
High Temperature Range.
ULT
Chip type, high voltage and high temperature range.
Load life of 2000 hours at +125°C.
Long Life
Applicable to automatic mounting machine
using carrier tape.
ULH
ULT
Compliant to the RoHS directive (2011/65/EU).
High
Voltage
UUB
Specifications
Item
Performance Characteristics
Category Temperature Range
Rated Voltage Range
–40 to +125°C
160 to 500V
Rated Capacitance Range
Capacitance Tolerance
1.8 to 33µF
20% at 120Hz, 20°C
Rated voltage (V)
–
~
160 450
500
Leakage Current
0.04CV+100(µA)max.(1 minute's at 20°C) 0.04CV+200(µA)max.(1 minute's at 20°C)
Measurement frequency : 120Hz at 20°C
Rated voltage (V)
160
200
250
400
450
500
Tangent of loss angle (tan δ)
tan δ (MAX.)
0.20
0.20
0.25
0.25
0.30
0.30
Measurement frequency : 120Hz
Rated voltage (V)
Impedance ratio
ZT / Z20 (MAX.)
160
200
6
250
10
400
10
450
15
500
15
Stability at Low Temperature
Z–40°C / Z+20°C
6
Capacitance change
tan δ
Leakage current
Within 30% of the initial capacitance value
300% or less than the intial specified value
Less than or equal to the initial specified value
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 2000 hours at 125°C.
Endurance
Shelf Life
After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
The capacitors are kept on a hot plate for 30 seconds,
Capacitance change
tan δ
Leakage current
Within 10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
which is maintained at 250°C and then performing voltage
treatment based on JIS C 5101-4 clause 4.1 at 20°C, they
shall meet the characteristic requirements listed at right
when they are removed from the plate.
Resistance to soldering
heat
Marking
Black print on the case top.
Chip Type
(φ8 , φ10)
Voltage(2G : 400V)
Series
Type numbering system (Example : 400V 6.8 F)
µ
1
2
3
4
5
6
7
8
9 10 11 12 13 14
Positive
Plastic platform
U L T 2 G 6 R 8 M N L 1 G S
C
0.2
0.3MAX.
Lot No.
Taping code
Configuration
Trade mark
Capacitance tolerance ( 20ꢀ)
Rated capacitance
Rated voltage
(
6.8µF
)
)
Capacitance
H
L
1.0
Negative
(
400V
Pressure relief vent
Series name
Type
(mm)
φD × L
8 × 10
2.9
8.3
8.3
3.1
10
10 × 10 10 × 13.5
A
3.2
10.3
10.3
4.5
3.2
10.3
10.3
4.5
B
C
E
L
Voltage
V
10
13.5
160 200 250 400 450 500
H
0.8 to 1.1 0.8 to 1.1 0.8 to 1.1
Code
2C
2D
2E
2G 2W 2H
Dimensions
V
160
200
2D
250
400
450
500
Cap.(µF)
1.8
3.3
3.9
4.7
5.6
6.8
7.5
8.2
10
Code
2C
2E
2G
2W
2H
1R8
3R3
3R9
4R7
5R6
6R8
7R5
8R2
100
120
150
180
220
270
330
8 × 10
20
35
8 × 10
20
10 × 10
8 × 10
30
45
50
10 × 13.5
40
10 × 10
35
40
10 × 10
10 × 13.5
8 × 10
30
10 × 13.5
12
8 × 10
45
60
65
15
8 × 10
45
10 × 10
45
50
18
10 × 10
10 × 13.5
22
10 × 10
60
65
27
10 × 13.5
Case size
φ D × L (mm)
Rated
ripple
33
10 × 13.5
Rated ripple current (mArms) at 125°C 120Hz
Taping specifications are given in page 23.
Recommended land size, soldering by reflow are given
in page 18, 19.
Frequency coefficient of rated ripple current
Frequency
50 Hz
120 Hz 300 Hz
1 kHz 10 kHz or more
Coefficient
0.70
1.00 1.17
1.36
1.50
Please refer to page 3 for the minimum order quantity.
146