Document 1610-1
Isolation Transformers
Halogen
Free
• Developed for Texas Instruments SN6501 and SN6505B
Push-Pull driver
• Low profile and center-tapped push-pull transformers for
isolated power supply
• 2500Vrms,oneminutehighisolation(hipot)windingtowinding
• AEC-Q200 Grade 1 (–40°C to +125°C)
Core material Ferrite
AEC
+
Q200 125°C
Terminations RoHS tin-silver-copper over tin over nickel over phos
bronze.
Weight 0.3 – 0.4 g
Ambient temperature –40°C to +125°C
Maximum part temperature +165°C (ambient + temp rise)
Storage temperature Component: –40°C to +165°C.
Tape and reel packaging: –40°C to +80°C
Resistance to soldering heat Max three 40 second reflows at
+260°C, parts cooled to room temperature between cycles
Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C /
85% relative humidity)
Packaging 1000 per 13″ reel Plastic tape: 24 mm wide, 0.4 mm thick,
12 mm pocket spacing, 4.6 mm pocket depth
PCB washing Tested to MIL-STD-202 Method 215 plus an additional
aqueous wash. See Doc787_PCB_Washing.pdf.
Leakage
DCR
max
Input
voltage
(V)
Lmin2
at 0 A
(µH)
L3
max
(µH)
Volt-time
product4
(V-µsec)
Part
Isolation5
(Vrms)
(Ohms)
Turns ratio
pri:sec
number1
pri
sec
Output
UA8251-AED
UA8252-AED
UA8253-AED
UA8254-AED
UA8255-AED
3.3
5.0
3.3
3.3
3.3
1050
900
900
900
900
0.35
0.35
1.2
1.0
1.7
0.306 0.334
0.320 0.360
0.320 0.550
0.320 0.440
0.320 0.670
1:1.13
1:1.076
1:1.693
1:1.308
1:2.0
10.4
11.5
11.5
11.5
11.5
2500
2500
2500
2500
2500
3.3 V
5 V
5 V
3.3 V
5 V
1. Packaging: D = 13″ machine ready reel.EIA-481 embossed plastic tape.
(1000 parts per full reel). Quantities less than full reel available: in tape
(not machine ready) or with leader and trailer ($25 charge).
2. Inductance is for primary windings measured at 10 kHz, 0.05Vrms, 0 Adc.
3. Leakage inductance measured between pins 1 and 3 at 100 kHz,
0.1 Vrms with secondary pins shorted.
4. Volt-time product is for primary windings, between pin 1 and 3.
5. One minute isolation (hipot) primary windings to secondary windings.
6. Electrical specifications at 25°C.
Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Schematics
1
2
3
6
5
SEC
PRI
4
inches
mm
Dimensions are in
Document 1610-1 Revised 09/20/22
US +1-847-639-6400 sales@coilcraft.com
UK +44-1236-730595 sales@coilcraft-europe.com
Taiwan +886-2-2264 3646 sales@coilcraft.com.tw
China +86-21-6218 8074 sales@coilcraft.com.cn
Singapore + 65-6484 8412 sales@coilcraft.com.sg
© Coilcraft Inc. 2023
This product may not be used in medical or high
risk applications without prior Coilcraft approval.
Specification subject to change without notice.
Please check web site for latest information.