TRS3222E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER
WITH ±15-kV ESD PROTECTION
www.ti.com
SLLS793–JUNE 2007
FEATURES
DB, DW, OR PW PACKAGE
•
ESD Protection for RS-232 Bus Pins
(TOP VIEW)
–
–
–
±15-kV Human-Body Model (HBM)
EN
C1+
1
2
3
4
5
6
7
8
9
10
20 PWRDOWN
±8-kV IEC61000-4-2, Contact Discharge
±15-kV IEC61000-4-2, Air-Gap Discharge
19
18
17
16
15
14
13
12
11
V
CC
V+
C1−
C2+
C2−
GND
•
Meets or Exceeds the Requirements of
TIA/EIA-232-F and ITU v.28 Standards
DOUT1
RIN1
ROUT1
N.C.
•
•
•
•
•
•
•
Operates With 3-V to 5.5-V VCC Supply
Operates up to 500 kbit/s
V−
DOUT2
RIN2
ROUT2
DIN1
DIN2
N.C.
Two Drivers and Two Receivers
Low Standby Current . . . 1 μA Typ
External Capacitors . . . 4 × 0.1 μF
Accepts 5-V Logic Input With 3.3-V Supply
N.C. − No internal connection
Alternative High-Speed Pin-Compatible Device
(1 Mbit/s) for TRS3222E
RHL PACKAGE
(TOP VIEW)
APPLICATIONS
•
•
•
•
•
•
Battery-Powered Systems
PDAs
Notebooks
Laptops
Palmtop PCs
Hand-Held Equipment
24
1
2
23
22
21
20
19
18
17
16
15
14
C1+
N.C.
V+
C1–
C2+
V
CC
3
N.C.
4
GND
DOUT1
RIN1
ROUT1
N.C.
DIN1
N.C.
DIN2
5
DESCRIPTION/ORDERING
INFORMATION
6
7
C2–
V–
DOUT2
N.C.
RIN2
8
The TRS3222E consists of two line drivers, two line
receivers, and a dual charge-pump circuit with
±15-kV ESD protection pin to pin (serial-port
connection pins, including GND).
9
10
11
12
13
The device meets the requirements of TIA/EIA-232-F
and provides the electrical interface between an
asynchronous communication controller and the
serial-port connector. The charge pump and four
small external capacitors allow operation from a
single 3-V to 5.5-V supply. The device operates at
typical data signaling rates up to 500 kbit/s and a
maximum of 30-V/μs driver output slew rate.
N.C. − No internal connection
The TRS3222E can be placed in the power-down mode by setting the power-down (PWRDOWN) input low,
which draws only 1 μA from the power supply. When the device is powered down, the receivers remain active
while the drivers are placed in the high-impedance state. Also, during power down, the onboard charge pump is
disabled; V+ is lowered to VCC, and V– is raised toward GND. Receiver outputs also can be placed in the
high-impedance state by setting enable (EN) high.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
UNLESS OTHERWISE NOTED this document contains
Copyright © 2007, Texas Instruments Incorporated
PRODUCTION DATA information current as of publication date.
Products conform to specifications per the terms of Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.