TPS27081A
www.ti.com
SLVSBE9A –APRIL 2012–REVISED JULY 2012
1.2 - 8V, 3A PFET High Side Load Switch with Level Shift & Adjustable Slew Rate Control
Check for Samples: TPS27081A
1
FEATURES
•
Low ON Resistance, High current PFET
DESCRIPTION
The TPS27081A IC is a high side load switch that
integrates a Power PFET and a Control NMOS in a
tiny package.
–
–
–
–
–
RDS(ON) = 32mΩ (Typ) at VGS = –4.5V
RDS(ON) = 44mΩ (Typ) at VGS =–3.0V
RDS(ON) = 85mΩ (Typ) at VGS = –1.8V
RDS(ON) = 85mΩ (Typ) at VGS = –1.5V
RDS(ON) = 155mΩ (Typ) at VGS = –1.2V
The TPS27081A is fully protected against ESD
strikes on all pins. The TPS27081A features industry-
standard ESD protection on all pins thus providing
better ESD compatibility with other on-board
components.
•
•
Adjustable Turn-ON and Turn-OFF slew rate
control through discrete components R1, R2,
and C1
The TPS27081A level shifts ON/OFF logic signal to
VIN levels and thus supports as low as 1.2V CPU or
MCU logic to control higher voltage power supplies
(VIN) without requiring an external level shifter.
Supports a wide range of 1.2V up to 8V supply
inputs
•
•
Integrated NMOS for Inrush current Control
NMOS Enable Supports a Wide Range of 1.2V
up to 8V Control logic Interface
Switching a large value output capacitor CL through a
fast ON/OFF logic signal may result in an excessive
inrush current. To control the load inrush current
connect a resistor R2, as shown in Figure 2 To
further limit the inrush current add an external
capacitor C1. To configure the TPS27081A to
achieve a specific slew rate refer to the Application
section.
•
•
Full Protection Against ESD (All Pins)
–
HBM 2kV, CDM 500V
Ultra Low Leakage Current in Stand-by (Typ
100nA)
•
•
–40°C to 85°C Temperature Rating
Available in Tiny 6-pin Packages
A single external component, R1, is required in
applications that do not require inrush current control.
In such applications connect the TPS27081A pin R2
to system ground.
–
2.9mm x 1.6mm Thin (0.9mm max) SOT-23
(DDC)
–
2mm x 2mm SON-6 (DRV) Preview Only
VOUT
VIN
Up to
8V
Supply
(4)
(2, 3)
ESD
Q1
ESD
LOAD
R1
CL
APPLICATIONS
(6)
(5)
C1
ESD
ESD
R1/C1
GPIO/
Logic
Q2
•
•
•
•
•
High Side Load Switch
Inrush-current control
ON/OFF
R2
(1)
R2
Power Sequencing and Control
Stand-by Power Isolation
Portable Power Switch
Figure 2. Simplified Block & Application Diagram
Component Table (Typical Application)
TPS27081ADDC
(TOP VIEW)
TPS27081ADRV PREVIEW ONLY
(TOP VIEW)
COMPONENT DESCRIPTION
6
R1/C1
ON/OFF
VIN
R2
VOUT
VOUT
1
2
3
R2
OUT
OUT
1
2
3
6
5
4
R1/C1
R1
R2
C1
Level Shift Pull-up Resistor
Optional(1)
Optional(1)
GND
(Thermal Pad)
ON/OFF
5
4
VIN
2mm x 2mm SON-6 (DRV)
2.9mm x 1.6mm x 0.75mm TSOT-23 (DDC)
Figure 1. TPS27081A Packages
(1) Required for load inrush current (slew rate) control
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCT PREVIEW information concerns products in the
formative or design phase of development. Characteristic data and
other specifications are design goals. Texas Instruments reserves
the right to change or discontinue these products without notice.
Copyright © 2012, Texas Instruments Incorporated