APPLICABLE STANDARD TIA/EIA-568-A CAT5 (note 1)
Operating
Storage temperature
range
-55 C to +85 C
temperature range
-25 C to +60 C
95 % max
-
1
△
Operating humidity
range
RATING Voltage
Current
125 V AC
Applicable cable
1 A
SPECIFICATIONS
TEST METHOD
ITEM
REQUIREMENTS
QT AT
CONSTRUCTION
Visually and by measuring instrument.
Confirmed visually.
According to drawing.
General Examination
X
X
X
X
Marking
ELECTRIC CHARACTERISTICS
Contact Resistance
100 mA max (DC or 1000 Hz AC).
50 m max.
X
X
(An example connector configuration is shown.)
100 V DC.
100 M min.
Insulation Resistance
X
X
X
X
500 V AC for 1 min.
No flashover or breakdown.
Voltage Proof
(Contact to Contact)
1500 V AC for 1 min.
No flashover or breakdown.
Voltage Proof
-
-
X
X
(Contact to Shield)
Near End Crosstalk
(NEXT) Loss
Measured minimum NEXT loss for each pair combination at 40 dB min.
100 MHz.
MECHANICAL CHARACTERISTICS
200 times insertions and extractions.
1) Contact resistance: 70 mΩ max.
Mechanical Operation
-
-
-
X
X
X
2) No damage, crack and looseness of parts.
1) No electrical discontinuity of 5 μs.
2) Contact resistance : 70 mΩ max.
Frequency 10 to 55 Hz, single amplitude 0.75 mm,
at 2 hours for 3 directions.
Vibration
490 m/s2 duration of pulse 11 ms at 3 times for 3 directions.
3) No damage, crack and looseness of parts.
Shock
ENVIRONMENTAL CHARACTERISTICS
Damp heat, Cyclic
Exposed at +40 C, 90 to 95 , 500 h
1) Contact resistance: 70 mΩ max.
2) Insulation resistance:
-
X
1 MΩ min.(At high humidity)
10 MΩ min.(At dry)
3) No damage, crack and looseness of parts.
1) Contact resistance : 70 m max.
2) Insulation resistance : 100 M min.
3) No damage, crack and looseness of parts.
1) Contact resistance : 70 m max.
2) No heavy corrosion.
Rapid Change of Temperature Temperature -55 → 5 to 35 → 85 → 5 to 35 ℃
-
X
Time
30 → 2 to 3 → 30 →2 to 3 min
Under 5 cycles.
Corrosion Salt Mist
Exposed in 5 % salt water spray for 48 h.
-
-
X
X
Resistance to Soldering heat
Flow
No deformation of case and excessive looseness of
the terminals.
Solder temperature, 260 ℃ max for Immersion, duration
10 s max.
Soldering iron
Soldering iron temperature, 350 ℃ max for immersion,
duration 5 s max.
Solderability
COUNT
Soldered at solder temperature, 245 ± 2 ℃ for immersion,
duration 3 ± 1 s.
Min. 95 % of solder immersed area shall be
-
X
covered new solder coating.
DESCRIPTION OF REVISIONS
DESIGNED
KIM JAEHYEON
CHECKED
DATE
DIS-E-00003598
TU.TANIGUCHI
20201127
1
2
△
REMARK
APPROVED
CHECKED
DESIGNED
DRAWN
MN.KENJO
20200407
20200407
20200407
20200407
Note 1. Applicable plug connector : TM21P-88P.
TU.TANIGUCHI
KIM JAEHYEON
DS.HIROWATARI
1
△
Unless otherwise specified, refer to IEC 60512.
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
DRAWING NO.
PART NO.
CODE NO.
ELC-123340-70-00
TM11R-5M2-88-LP(70)
SPECIFICATION SHEET
HIROSE ELECTRIC CO., LTD.
1
△
1/1
CL0222-2905-0-70
FORM HD0011-2-1