APPLICABLE STANDARD TIA/EIA-568-A CAT5 (note 1)
Operating
Storage temperature
range
-55 C to +85 C
temperature range
-25 C to +60 C
95 % max
-
Operating humidity
range
RATING Voltage
Current
125 V AC
Applicable cable
1 A
SPECIFICATIONS
TEST METHOD
ITEM
REQUIREMENTS
QT AT
CONSTRUCTION
Visually and by measuring instrument.
Confirmed visually.
According to drawing.
General Examination
X
X
X
X
Marking
ELECTRIC CHARACTERISTICS
Contact Resistance
100 mA max (DC or 1000 Hz AC).
50 m max.
X
X
100 mm
Plug
Modular cable
Receptacle
Measurement point
(An example connector configuration is shown.)
100 V DC.
100 M min.
Insulation Resistance
X
X
X
X
500 V AC for 1 min.
No flashover or breakdown.
Voltage Proof
(Contact to Contact)
1500 V AC for 1 min.
No flashover or breakdown.
40 dB min.
Voltage Proof
-
-
X
X
(Contact to Shield)
Near End Crosstalk
(NEXT) Loss
Measured NEXT LOSS for 1,2-3,6 pair combination at
100 MHz.
MECHANICAL CHARACTERISTICS
200 times insertions and extractions.
1) Contact resistance: 70 mΩ max.
Mechanical Operation
-
-
-
X
X
X
2) No damage, crack and looseness of parts.
1) No electrical discontinuity of 5 μs.
Frequency 10 to 55 Hz, single amplitude 0.75 mm,
1 octave / min, 3 axial directions, 10 cycles each.
490 m/s2 duration of pulse 11 ms
Vibration
2) No damage, crack and looseness of parts.
Shock
at 3 times in 3 both axial directions.
ENVIRONMENTAL CHARACTERISTICS
Damp heat, Cyclic
Exposed at +40 C, 90 to 95 , 500 h
1) Contact resistance: 70 mΩ max.
2) Insulation resistance:
-
-
X
X
1 MΩ min.(At high humidity)
10 MΩ min.(At dry)
3) No damage, crack and looseness of parts.
1) Contact resistance : 70 m max.
2) Insulation resistance : 100 M min.
3) No damage, crack and looseness of parts.
Rapid Change of Temperature Temperature -55 ± 3 → 85 ± 2 ℃
Time
30 → 30 min
Under 5 cycles.
Chamber transfer time is 2 to 3 min.
Corrosion Salt Mist
Resistance to Soldering heat
Solderability
Exposed in 5 % salt water spray for 48 h.
1) Contact resistance : 70 m max.
2) No heavy corrosion.
-
-
-
X
X
X
Solder temperature, 260 ± 5 ℃ for immersion,
No deformation of case and excessive looseness of
the terminals.
duration 5 ± 1 s.
2
△
Soldered at solder temperature, 245 ± 2 ℃ for immersion,
Min. 95 % of solder immersed area shall be
covered new solder coating.
duration 3 ± 1 s.
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
MO.SHIMOYAMA
CHECKED
DATE
DIS-E-00005214
TU.TANIGUCHI
20210420
2
1
△
REMARK
APPROVED
CHECKED
DESIGNED
DRAWN
MN.KENJO
20200403
20200403
20200403
20200403
Note 1. Applicable plug connector : TM21P-88P.
TU.TANIGUCHI
KIM JAEHYEON
DS.HIROWATARI
Unless otherwise specified, refer to IEC 60512.
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
DRAWING NO.
PART NO.
CODE NO.
ELC-123343-70-00
TM11R-5M2-88(70)
SPECIFICATION SHEET
HIROSE ELECTRIC CO., LTD.
2
1/1
CL0222-2906-2-70
△
FORM HD0011-2-1