5秒后页面跳转
TLE2662IDW PDF预览

TLE2662IDW

更新时间: 2024-11-23 04:28:07
品牌 Logo 应用领域
德州仪器 - TI 转换器开关运算放大器放大器电路光电二极管输入元件
页数 文件大小 规格书
40页 588K
描述
DUAL uPOWER JFET-INPUT OPERATIONAL AMPLIFIER WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER

TLE2662IDW 技术参数

是否无铅: 含铅是否Rohs认证: 不符合
生命周期:Obsolete零件包装代码:SOIC
包装说明:SO-16针数:16
Reach Compliance Code:not_compliantECCN代码:EAR99
HTS代码:8542.33.00.01Factory Lead Time:1 week
风险等级:5.4Is Samacsys:N
放大器类型:OPERATIONAL AMPLIFIER架构:VOLTAGE-FEEDBACK
最大平均偏置电流 (IIB):0.005 µA25C 时的最大偏置电流 (IIB):0.005 µA
最小共模抑制比:65 dB标称共模抑制比:65 dB
频率补偿:YES最大输入失调电压:5300 µV
JESD-30 代码:R-PDSO-G16长度:10.3 mm
低-偏置:YES低-失调:NO
微功率:YES负供电电压上限:-16 V
标称负供电电压 (Vsup):-15 V功能数量:2
端子数量:16最高工作温度:85 °C
最低工作温度:-40 °C封装主体材料:PLASTIC/EPOXY
封装代码:SOP封装等效代码:SOP16,.4
封装形状:RECTANGULAR封装形式:SMALL OUTLINE
峰值回流温度(摄氏度):NOT SPECIFIED电源:+-5/+-15 V
认证状态:Not Qualified座面最大高度:2.65 mm
最小摆率:2.1 V/us标称压摆率:3.4 V/us
子类别:Operational Amplifier最大压摆率:0.72 mA
供电电压上限:16 V标称供电电压 (Vsup):15 V
表面贴装:YES技术:BIPOLAR
温度等级:INDUSTRIAL端子形式:GULL WING
端子节距:1.27 mm端子位置:DUAL
处于峰值回流温度下的最长时间:NOT SPECIFIED标称均一增益带宽:1500 kHz
最小电压增益:10000宽度:7.5 mm
Base Number Matches:1

TLE2662IDW 数据手册

 浏览型号TLE2662IDW的Datasheet PDF文件第2页浏览型号TLE2662IDW的Datasheet PDF文件第3页浏览型号TLE2662IDW的Datasheet PDF文件第4页浏览型号TLE2662IDW的Datasheet PDF文件第5页浏览型号TLE2662IDW的Datasheet PDF文件第6页浏览型号TLE2662IDW的Datasheet PDF文件第7页 
TLE2662  
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER  
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER  
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994  
DW PACKAGE  
(TOP VIEW)  
Single-Supply Operation With Rail-to-Rail  
Inputs  
= 0.000 V While Sinking 25 mA  
V
OL  
1
2
3
4
5
6
7
8
16  
15  
14  
13  
12  
11  
10  
9
1OUT  
1IN–  
1IN+  
V
CC+  
2OUT  
Wide V  
Range . . . 3.5 V to 15 V  
CC  
SCOUT Supplies up to 100 mA for External  
Loads  
2IN–  
2IN+  
CAP–  
GND  
CAP+  
FB/SD  
V
CC–  
Shutdown Mode  
SCOUT  
SCREF  
OSC  
External 2.5-V Voltage Reference Available  
description  
SCIN  
TheTLE2662offerstheadvantagesofJFET-input  
operational amplifiers and rail-to-rail common-  
mode input voltage range with the convenience of single-supply operation. By combining a switched-capacitor  
voltage converter with a dual operational amplifier in a single package, Texas Instruments now gives circuit  
designers new options for conditioning low-level signals in single-supply systems.  
The TLE2662 features two low power, high-output drive JFET-input operational amplifiers with a switched-  
capacitor building block. Using two external capacitors, the switched-capacitor network can be configured as  
a voltage inverter, generating a negative supply voltage capable of sourcing up to 100 mA. This supply functions  
not only as the amplifier negative rail but is also available to drive external circuitry. In this configuration, the  
amplifier common-mode input voltage range extends from the positive rail to below ground, providing true  
rail-to-rail inputs from a single supply. Furthermore, the outputs can swing to and below ground while sinking  
over 25 mA. This feature was previously unavailable in operational amplifier circuits. The TLE2662 operational  
amplifier section has output stages that can drive 100-loads to 2.5 V from a 5-V rail. With a 10-kload, the  
output swing extends to 3.5 V and can include the positive rail with a pullup resistor.  
This operational amplifier offers the high slew rate, wide bandwidth, and high input impedance commonly  
associated with JFET-input amplifiers, making the TLE2662 operational amplifier section suited for amplifying  
fast signals without loading the signal source. When not sourcing or sinking current into a load, the amplifier  
consumes only microamperes of supply current, thereby reducing the drain on and extending the life of the  
power supply.  
The TLE2662 features a shutdown pin (FB/SD), which can be used to disable the switched capacitor section.  
When disabled, the voltage converter block draws less than 150 µA from the power supply. This feature,  
combined with the operational amplifier’s low quiescent current, makes the TLE2662 a real power saver in the  
standby mode.  
The switched-capacitor building block also provides an on-board regulator; with the addition of an external  
divider, awell-regulatedoutputvoltageiseasilyobtained. Additionalfilteringcanbeaddedtominimizeswitching  
noise. The internal oscillator runs at a nominal frequency of 25 kHz. This can be synchronized to an external  
clock signal or can be varied using an external capacitor. A 2.5-V reference is brought out to SCREF for use  
with the on-board regulator or external circuitry.  
TheTLE2662ischaracterizedforoperationovertheindustrialtemperaturerangeof 40°Cto85°C. Thisdevice  
is available in a 16-pin wide-body surface-mount package.  
AVAILABLE OPTION  
PACKAGE  
T
A
SMALL OUTLINE  
(DW)  
40°C to 85°C  
TLE2662IDW  
The DW package is available taped and reeled. Add  
the suffix R to the device type (i.e., TLE2662IDWR).  
Copyright 1994, Texas Instruments Incorporated  
PRODUCTION DATA information is current as of publication date.  
Products conform to specifications per the terms of Texas Instruments  
standard warranty. Production processing does not necessarily include  
testing of all parameters.  
1
POST OFFICE BOX 655303 DALLAS, TEXAS 75265  

TLE2662IDW 替代型号

型号 品牌 替代类型 描述 数据表
TLE2662IDWR TI

功能相似

DUAL uPOWER JFET-INPUT OPERATIONAL AMPLIFIER WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER

与TLE2662IDW相关器件

型号 品牌 获取价格 描述 数据表
TLE2662IDWR TI

获取价格

DUAL uPOWER JFET-INPUT OPERATIONAL AMPLIFIER WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
TLE2682 TI

获取价格

HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIER WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
TLE2682IDW TI

获取价格

High-Speed JFET-Input Dual Operational Amplifier w/Switched-Capacitor Voltage Converter 16
TLE2682IDWR TI

获取价格

HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIER WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
TLE3101 INFINEON

获取价格

BIPOLAR IC
TLE3102 INFINEON

获取价格

BIPOLAR IC
TLE3103 INFINEON

获取价格

BIPOLAR IC
TLE3104 INFINEON

获取价格

BIPOLAR IC
TLE3303AF100QG E-SWITCH

获取价格

TACT SWITCHES SMT - 6mm x 6mm
TLE3303AF160QG E-SWITCH

获取价格

TACT SWITCHES SMT - 6mm x 6mm