5秒后页面跳转
TLE2141AMJGB PDF预览

TLE2141AMJGB

更新时间: 2024-11-18 22:30:07
品牌 Logo 应用领域
德州仪器 - TI 运算放大器放大器电路
页数 文件大小 规格书
60页 895K
描述
EXCALIBUR LOW NOISE HIGH SPEED PRECISION OPERATIONAL AMPLIFIERS

TLE2141AMJGB 技术参数

生命周期:Active零件包装代码:DIP
包装说明:CERAMIC, DIP-8针数:8
Reach Compliance Code:not_compliantECCN代码:EAR99
HTS代码:8542.33.00.01Factory Lead Time:1 week
风险等级:5.38Is Samacsys:N
放大器类型:OPERATIONAL AMPLIFIER架构:VOLTAGE-FEEDBACK
最大平均偏置电流 (IIB):1.5 µA25C 时的最大偏置电流 (IIB):2 µA
最小共模抑制比:85 dB标称共模抑制比:108 dB
频率补偿:YES最大输入失调电流 (IIO):0.1 µA
最大输入失调电压:900 µVJESD-30 代码:R-GDIP-T8
长度:9.6 mm低-偏置:NO
低-失调:NO微功率:NO
负供电电压上限:-22 V标称负供电电压 (Vsup):-15 V
功能数量:1端子数量:8
最高工作温度:125 °C最低工作温度:-55 °C
封装主体材料:CERAMIC, GLASS-SEALED封装代码:DIP
封装等效代码:DIP8,.3封装形状:RECTANGULAR
封装形式:IN-LINE包装方法:TUBE
峰值回流温度(摄氏度):NOT SPECIFIED功率:NO
电源:5/+-15 V可编程功率:NO
认证状态:Not Qualified筛选级别:MIL-STD-883
座面最大高度:5.08 mm最小摆率:27 V/us
标称压摆率:45 V/us子类别:Operational Amplifier
最大压摆率:4.5 mA供电电压上限:22 V
标称供电电压 (Vsup):15 V表面贴装:NO
技术:BIPOLAR温度等级:MILITARY
端子形式:THROUGH-HOLE端子节距:2.54 mm
端子位置:DUAL处于峰值回流温度下的最长时间:NOT SPECIFIED
标称均一增益带宽:6000 kHz最小电压增益:5000
宽带:NO宽度:6.67 mm
Base Number Matches:1

TLE2141AMJGB 数据手册

 浏览型号TLE2141AMJGB的Datasheet PDF文件第2页浏览型号TLE2141AMJGB的Datasheet PDF文件第3页浏览型号TLE2141AMJGB的Datasheet PDF文件第4页浏览型号TLE2141AMJGB的Datasheet PDF文件第5页浏览型号TLE2141AMJGB的Datasheet PDF文件第6页浏览型号TLE2141AMJGB的Datasheet PDF文件第7页 
ꢁ ꢂꢃ ꢄ ꢅ ꢆ ꢇ ꢈ ꢁꢂ ꢃꢄ ꢅꢆ ꢇꢉ  
ꢃꢊ ꢋꢉꢂ ꢌꢍꢎ ꢏ ꢂ ꢐ ꢑꢒꢓꢐ ꢌꢔ ꢃ ꢕꢌ ꢖ ꢕꢒ ꢔꢗ ꢃ ꢃꢘ  
ꢗꢏꢃ ꢋꢌꢔ ꢌꢐ ꢓ ꢐ ꢗꢃꢏ ꢉꢁ ꢌꢐ ꢓꢉꢂ ꢉꢙ ꢗ ꢂꢌ ꢚꢌ ꢃꢏ ꢔ  
SLOS183B − FEBRUARY 1997 − REVISED APRIL 2004  
D
Low Noise  
D
D
Single or Split Supply . . . 4 V to 44 V  
10 Hz . . . 15 nV/Hz  
1 kHz . . . 10.5 nV/Hz  
10000-pF Load Capability  
Fast Settling Time  
340 ns to 0.1%  
D
D
D
D
D
400 ns to 0.01%  
20-mA Min Short-Circuit Output Current  
D
D
Saturation Recovery . . . 150 ns  
27-V/µs Min Slew Rate  
High Gain-Bandwidth Product . . . 5.9 MHz  
Large Output Swing  
V
+0.1 V to V  
− 1 V  
CC−  
CC+  
Low V  
. . . 500 µV Max at 25°C  
IO  
description  
The TLE214x and TLE214xA devices are high-performance, internally compensated operational amplifiers  
built using Texas Instruments complementary bipolar Excalibur process. The TLE214xA is a tighter offset  
voltage grade of the TLE214x. Both are pin-compatible upgrades to standard industry products.  
The design incorporates an input stage that simultaneously achieves low audio-band noise of 10.5 nV/Hz with  
a 10-Hz 1/f corner and symmetrical 40-V/µs slew rate typically with loads up to 800 pF. The resulting low  
distortion and high power bandwidth are important in high-fidelity audio applications. A fast settling time of  
340 ns to 0.1% of a 10-V step with a 2-k/100-pF load is useful in fast actuator/positioning drivers. Under similar  
test conditions, settling time to 0.01% is 400 ns.  
The devices are stable with capacitive loads up to 10 nF, although the 6-MHz bandwidth decreases to 1.8 MHz  
at this high loading level. As such, the TLE214x and TLE214xA are useful for low-droop sample-and-holds and  
direct buffering of long cables, including 4-mA to 20-mA current loops.  
The special design also exhibits an improved insensitivity to inherent integrated circuit component mismatches  
as is evidenced by a 500-µV maximum offset voltage and 1.7-µV/°C typical drift. Minimum common-mode  
rejection ratio and supply-voltage rejection ratio are 85 dB and 90 dB, respectively.  
Device performance is relatively independent of supply voltage over the 2-V to 22-V range. Inputs can  
operate between V  
− 0.3 to V  
− 1.8 V without inducing phase reversal, although excessive input current  
CC−  
CC+  
may flow out of each input exceeding the lower common-mode input range. The all-npn output stage provides  
a nearly rail-to-rail output swing of V − 0.1 to V − 1 V under light current-loading conditions. The device  
CC−  
CC+  
can sustain shorts to either supply since output current is internally limited, but care must be taken to ensure  
that maximum package power dissipation is not exceeded.  
Both versions can also be used as comparators. Differential inputs of V  
can be maintained without damage  
CC  
to the device. Open-loop propagation delay with TTL supply levels is typically 200 ns. This gives a good  
indication as to output stage saturation recovery when the device is driven beyond the limits of recommended  
output swing.  
Both the TLE214x and TLE214xA are available in a wide variety of packages, including both the  
industry-standard 8-pin small-outline version and chip form for high-density system applications. The C-suffix  
devices are characterized for operation from 0°C to 70°C, I-suffix devices from 40°C to 105°C, and M-suffix  
devices over the full military temperature range of 55°C to 125°C.  
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of  
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.  
ꢁꢦ  
Copyright 1997 − 2004, Texas Instruments Incorporated  
ꢢ ꢦ ꢣ ꢢꢛ ꢜꢯ ꢞꢝ ꢡ ꢩꢩ ꢧꢡ ꢟ ꢡ ꢠ ꢦ ꢢ ꢦ ꢟ ꢣ ꢫ  
1
POST OFFICE BOX 655303 DALLAS, TEXAS 75265  

与TLE2141AMJGB相关器件

型号 品牌 获取价格 描述 数据表
TLE2141AML TI

获取价格

IC,OP-AMP,SINGLE,BIPOLAR,CAN,8PIN,METAL
TLE2141AMP TI

获取价格

EXCALIBUR LOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIERS
TLE2141CD TI

获取价格

EXCALIBUR LOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIERS
TLE2141CDG4 TI

获取价格

EXCALIBUR LOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIERS
TLE2141CDR TI

获取价格

EXCALIBUR LOW NOISE HIGH SPEED PRECISION OPERATIONAL AMPLIFIERS
TLE2141CDRG4 TI

获取价格

EXCALIBUR LOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIERS
TLE2141CP TI

获取价格

EXCALIBUR LOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIERS
TLE2141CPE4 TI

获取价格

EXCALIBUR LOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIERS
TLE2141-EP TI

获取价格

Excalibur™ LOW-NOISE HIGH-SPEED PRECISION OPE
TLE2141-EP_12 TI

获取价格

Excalibur LOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIER