TFM-1XX-XX-XXX-D-XXX
NOTES:
REVISION FK
OPTION
C
1.
REPRESENTS A CRITICAL DIMENSION.
-A: ALIGNMENT PIN (USE TFM-XX-D-XX-A,
SEE TABLE 1) (SEE FIG 8, SHT 3)
No OF POSITIONS
2. MINIMUM PUSHOUT FORCE FOR CONTACTS, WELD TABS, C
AND THREADED INSERTS: 12 OZ.
LEAD STYLE -01, -02, -03: -02 THRU -50 (ALL
POSITIONS AVAILABLE)
(NOT AVAILABLE FOR -RA OR -REX)
-LC: LOCKING CLIP (USE LC-05-TM)
(NOT AVAILABLE FOR -RA OR -REX)
(SEE FIG 10, SHT 3 & NOTES 3 & 11)
-P: PICK AND PLACE PAD (USE PPP-04)
(AVAILABLE IN ALL POSITIONS -05 THRU
-50 EXCEPT -05 WITH -WT)
DO NOT
SCALE FROM
THIS PRINT
3. MINIMUM LOCKING CLIP RETENTION: 8 OZS.
4. MAXIMUM HEIGHT VARIATION BETWEEN ANY TWO PINS: .005[0.13] LEAD STYLES -11, -12, -13: (-05 THRU -50 MULTIPLES OF 5)
POSITIONS 12, 16, 17 ALSO AVAILABLE
LEAD STYLES -21, 22, 23: (-05 THRU -50 MULTIPLES OF 5)
POSITIONS 12 & 13 ALSO AVAILABLE
5. MAXIMUM TERMINAL BURR: .003[0.08]
6. COPLANARITY: .004[0.10] = POS 02 THRU 26
.006[0.15] = POS 27 THRU 50
C
LEAD STYLES 31, 32: 12 POSITION ALSO AVAILABLE
7. MEASURED FROM BEND.
8. DIMENSION CHANGED PER REVISION AD. CONTACT ENGINEERING
FOR INFORMATION.
(NOT AVAILABLE FOR -RA OR -REX,
SEE FIG 7, SHT 3)
LEAD STYLE
9. MEASURE FROM TIPS OF PIN.
10. NOTE DELETED.
-RA: RIGHT ANGLE
THROUGH HOLE
-01, -03 (SEE FIG 1)
-11, -13 (SEE FIG 1)
-21,-23 (SEE FIG 1)
-31 (SEE FIG 1)
SURFACE MOUNT
-02 (SEE FIG 2)
-12 (SEE FIG 2)
-22 (SEE FIG 2)
-32 (SEE FIG 2)
(AVAILABLE ONLY IN LEAD STYLE: -01
SEE FIG 5, SHT 2)
11. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED,
THE –LC OPTION IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC
RECOMMENDS MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE
–LC OPTION.
-TR: TAPE AND REEL (SEE FIG 4, SHT 7)
(NOT AVAILABLE WITH -DS OPTION
OR THROUGH HOLE LEAD STYLE)
-SA: STAKED ALIGNMENT PIN (SEE FIG 9, SHT 3)
(ONLY AVAILABLE ON SURFACE MOUNT
LEAD STYLE)
12. SIDES OF PLASTIC BODIES ON ALL LEAD STYLES EXCEPT THE -01, -02 & -03
WILL BE SOLID AND WITHOUT SIDE SLOTS.
13. NOTE DELETED.
PLATING SPECIFICATION
-S: 30µ" SELECTIVE GOLD ON CONTACT AREA,
MATTE TIN TAIL
-K: POLYIMIDE FILM (SEE FIG 3, SHT 2)
(USE K-DOT-.217-.313-.005)
-L: 15µ" SELECTIVE GOLD ON CONTACT AREA,
MATTE TIN TAIL
(No OF POSITIONS x .050[1.27]) + .125[3.18] REF
(No OF POSITIONS x .050[1.27]) + .025[.64] REF
(NOT AVAILABLE FOR -RA OR -REX)
(ALL LEAD STYLES EXCEPT -21 AVAILABLE)
-WT: WELD TABS (USE WT-25-XX-T)
(AVAILABLE ON -01, -02 & -03 LEAD
STYLES ONLY) (SEE FIG 6, SHT 2)
(MATES WITH SFSS/SFSD -SR & -DR ONLY)
(NOT AVAILABLE WITH -A, -LC,
-F: 3µ" FLASH GOLD ON CONTACT AREA,
MATTE TIN TAIL
-H: 30µ" SELECTIVE GOLD ON CONTACT AREA,
3µ" FLASH GOLD ON TAIL
.110 2.79 REF
02
-SM: 30µ" SELECTIVE GOLD ON CONTACT AREA,
MATTE TIN TAIL
-LM: 15µ" SELECTIVE GOLD ON CONTACT AREA,
MATTE TIN TAIL
.155 3.94
REF
-RA, OR -SA OPTIONS)
-FM: 3µ" FLASH GOLD ON CONTACT AREA,
MATTE TIN TAIL
-RE1: RIGHT ANGLE ELEVATED .062 PCB
(USE TFM-XX-D-01-RE, NOT AVAILABLE
WITHOUT -WT, AVAILABLE IN LEAD
STYLE -01 ONLY, -03 THRU -50 POS)
(MATES WITH SFSS/SFSD -SR & -DR ONLY)
(SEE FIG 11, SHT 4)
-STL: 30µ" SELECTIVE GOLD ON CONTACT AREA,
TIN/LEAD (90/10 ±5%) TAIL
01
.050 1.27
REF
.225 5.72
REF
.075 1.91
REF
BODY SPECIFICATION
-RE2: RIGHT ANGLE ELEVATED .093 PCB
(USE TFM-XX-D-01-RE, NOT AVAILABLE
WITHOUT -WT, AVAILABLE IN LEAD
STYLE -01 ONLY, -03 THRU -50 POS)
(MATES WITH SFSS/SFSD -SR & -DR ONLY)
(SEE FIG 11, SHEET 4)
-D: DOUBLE ROW
C
.050 1.27
(No OF POSITIONS x .050[1.27]) - .050[1.27]
2
MAX SWAY
(EITHER DIRECTION)
.018 0.46 REF
-SN: SOLDER NAIL FOR .062 BOARD
(TFM-XX-D-01-SN AND WT-27-01-T)
(SEE FIG12, SHT 3)
.135 3.43 REF
"D" REF
2
MAX SWAY
"A"
(SEE TABLE 1,
SHT 7)
(EITHER DIRECTION)
(ONLY AVAILABLE WITH -02 LEAD STYLE)
(NOT AVAILABLE WITH OPTIONS -A, -LC,
-RA, -SA, -WT, -RE1 OR -RE2)
.096 2.44
(SEE NOTE 8)
.1635 4.153
REF
"A" REF
(SEE TABLE 1,
SHT 7)
-SN2: SOLDER NAIL FOR .093 BOARD
(TFM-XX-D-01-SN AND WT-27-02-T)
(SEE FIG12, SHT 3)
(ONLY AVAILABLE WITH -02 LEAD STYLE)
(NOT AVAILABLE WITH OPTIONS -A, -LC,
-RA, -SA, -WT, -RE1 OR -RE2)
SEE NOTE 12
-DS: DUAL SCREW DOWN FOR .062 BOARD
(SEE FIG 18, SHT 5)
.010 0.25 REF
C
.014 0.36 REF
MAX SWAY
.050 1.27
"A"
"J" ± .003 [0.08]
(SEE TABLE 1, SHT 7)
C
(ONLY AVAILABLE WITH -01 & -02 LEAD STYLE)
(NOT AVAILABLE WITH OPTIONS -A, -LC, -P,
-RA, -TR, -SA, -K, -WT, -RE1, -RE2, -SN, -SN2)
(-01 LEAD STYLE USES TFM-XX-D-01-DSL
& T1-M2-4-VSFM-T, 02 LEAD STYLE USES
TFM-XX-D-01-DSA & T1-M2-4-VSFM-T)
2
(EITHER DIRECTION)
C
2
MAX SWAY
(EITHER DIRECTION)
SECTION "A"-"A"
(No OF POSITIONS x .050[1.27]) - .050[1.27]
C
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS CONFIDENTIAL AND
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
*
*
PROPRIETARY INFORMATION AND ALL DESIGN,
TOLERANCES ARE:
DECIMALS
MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS
AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC,
INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE
OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR
REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY
OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS
WRITTEN CONSENT OF SAMTEC, INC.
ANGLES
2
"C"±.003 [0.08]
(SEE TABLE 1,
C
.XX: .01[0.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
FIG 1
.XXX: .005[0.13]
PHONE: 812-944-6733
FAX: 812-948-5047
code 55322
.XXXX: .0020[0.051]
THROUGH HOLE
e-Mail info@SAMTEC.com
SHT 7)
-01, -03, -11, -13, -21, -23, -31
SHEET SCALE: 2.5:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
INSULATOR:
.050 X .050 TERMINAL STRIP
LCP, UL 94-VO
COLOR: BLACK
NO. TFM-1XX-XX-XXX-D-XXX
DWG.
IN-PROCESS
TERMINAL: PHOSPHOR BRONZE
SHEET 1 OF 7
F:\DWG\MISC\MKTG\TFM-1XX-XX-XXX-D-XXX-MKT.SLDDRW
BY:
garyp
11/5/2014
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
