NOTES:
TFM-1XX-XX-XXX-D-XXX
REVISION FE
C
OPTION
1.
REPRESENTS A CRITICAL DIMENSION.
No OF POSITIONS
2. MINIMUM PUSHOUT FORCE FOR CONTACTS, WELD TABS,
AND THREADED INSERTS: 12 OZ.
3. MINIMUM LOCKING CLIP RETENTION: 8 OZS.
4. MAXIMUM HEIGHT VARIATION BETWEEN ANY TWO PINS: .005[0.13]
5. MAXIMUM TERMINAL BURR: .003[0.08]
6. COPLANARITY: .004[0.10] = POS 02 THRU 26
.006[0.15] = POS 27 THRU 50
7. MEASURED FROM BEND.
8. DIMENSION CHANGED PER REVISION AD. CONTACT ENGINEERING
FOR INFORMATION.
9. MEASURE FROM TIPS OF PIN.
10. THIS FEATURE ONLY PRESENT ON -01 &-02 LEAD STYLES.
11. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED,
THE –LC OPTION IS NOT COMPATIBLE WITH AUTO PLACEMENT. SAMTEC
RECOMMENDS MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE
–LC OPTION.
12. SIDES OF PLASTIC BODIES ON ALL LEAD STYLES EXCEPT THE -01, -02 & -03
WILL BE SOLID AND WITHOUT SIDE SLOTS.
13. NOTE DELETED.
-A: ALIGNMENT PIN (USE TFM-XX-D-XX-A,
SEE TABLE 1) (SEE FIG 8, SHT 3)
LEAD STYLE -01, -02, -03: -02 THRU -50 (ALL
DO NOT
SCALE FROM
THIS PRINT
POSITIONS AVAILABLE)
(NOT AVAILABLE FOR -RA OR -REX)
-LC: LOCKING CLIP (USE LC-05-TM)
(NOT AVAILABLE FOR -RA OR -REX)
(SEE FIG 10, SHT 3 & NOTES 3 & 11)
-P: PICK AND PLACE PAD (USE PPP-04)
(AVAILABLE IN ALL POSITIONS -05 THRU
-50 EXCEPT -05 WITH -WT)
LEAD STYLES -11, -12, -13: (-05 THRU -50 MULTIPLES OF 5)
POSITIONS 12, 16, 17 ALSO AVAILABLE
LEAD STYLES -21, 22, 23: (-05 THRU -50 MULTIPLES OF 5)
POSITIONS 12 & 13 ALSO AVAILABLE
C
LEAD STYLES 31, 32: 12 POSITION ALSO AVAILABLE
(NOT AVAILABLE FOR -RA OR -REX,
SEE FIG 7, SHT 3)
LEAD STYLE
-RA: RIGHT ANGLE
THROUGH HOLE
-01, -03 (SEE FIG 1)
-11, -13 (SEE FIG 1)
-21,-23 (SEE FIG 1)
-31 (SEE FIG 1)
SURFACE MOUNT
-02 (SEE FIG 2)
-12 (SEE FIG 2)
-22 (SEE FIG 2)
-32 (SEE FIG 2)
(AVAILABLE ONLY IN LEAD STYLE: -01
SEE FIG 5, SHT 2)
-TR: TAPE AND REEL (SEE FIG 4, SHT 7)
(NOT AVAILABLE WITH -DS OPTION
OR THROUGH HOLE LEAD STYLE)
-SA: STAKED ALIGNMENT PIN (SEE FIG 9, SHT 3)
(ONLY AVAILABLE ON SURFACE MOUNT
LEAD STYLE)
PLATING SPECIFICATION
-S: 30µ" SELECTIVE GOLD ON CONTACT AREA,
MATTE TIN TAIL
-L: 15µ" SELECTIVE GOLD ON CONTACT AREA,
MATTE TIN TAIL
-K: POLYIMIDE FILM (SEE FIG 3, SHT 2)
(USE K-DOT-.217-.313-.005)
(No OF POSITIONS x .050[1.27]) + .125[3.18] REF
(No OF POSITIONS x .050[1.27]) + .025[.64] REF
-F: 3µ" FLASH GOLD ON CONTACT AREA,
MATTE TIN TAIL
(NOT AVAILABLE FOR -RA OR -REX)
(ALL LEAD STYLES EXCEPT -21 AVAILABLE)
-WT: WELD TABS (USE WT-25-XX-T)
(AVAILABLE ON -01, -02 & -03 LEAD
STYLES ONLY) (SEE FIG 6, SHT 2)
(MATES WITH SFSS/SFSD -SR & -DR ONLY)
(NOT AVAILABLE WITH -A, -LC,
-H: 30µ" SELECTIVE GOLD ON CONTACT AREA,
3µ" FLASH GOLD ON TAIL
.110 2.79 REF
02
-SM: 30µ" SELECTIVE GOLD ON CONTACT AREA,
MATTE TIN TAIL
-LM: 15µ" SELECTIVE GOLD ON CONTACT AREA,
MATTE TIN TAIL
.155 3.94
REF
-RA, OR -SA OPTIONS)
-FM: 3µ" FLASH GOLD ON CONTACT AREA,
MATTE TIN TAIL
-RE1: RIGHT ANGLE ELEVATED .062 PCB
(USE TFM-XX-D-01-RE, NOT AVAILABLE
WITHOUT -WT, AVAILABLE IN LEAD
STYLE -01 ONLY, -03 THRU -50 POS)
(MATES WITH SFSS/SFSD -SR & -DR ONLY)
(SEE FIG 11, SHT 4)
-RE2: RIGHT ANGLE ELEVATED .093 PCB
(USE TFM-XX-D-01-RE, NOT AVAILABLE
WITHOUT -WT, AVAILABLE IN LEAD
STYLE -01 ONLY, -03 THRU -50 POS)
(MATES WITH SFSS/SFSD -SR & -DR ONLY)
(SEE FIG 11, SHEET 4)
-STL: 30µ" SELECTIVE GOLD ON CONTACT AREA,
TIN/LEAD (90/10 ±5%) TAIL
01
.050 1.27
REF
.225 5.72
REF
SEE NOTE 10
.075 1.91
REF
BODY SPECIFICATION
-D: DOUBLE ROW
C
.050 1.27
(No OF POSITIONS x .050[1.27]) - .050[1.27]
2
MAX SWAY
(EITHER DIRECTION)
.018 0.46 REF
.135 3.43 REF
-SN: SOLDER NAIL FOR .062 BOARD
(TFM-XX-D-01-SN AND WT-27-01-T)
(SEE FIG12, SHT 3)
"D" REF
2
MAX SWAY
"A"
(SEE TABLE 1,
SHT 7)
(EITHER DIRECTION)
(ONLY AVAILABLE WITH -02 LEAD STYLE)
(NOT AVAILABLE WITH OPTIONS -A, -LC,
-RA, -SA, -WT, -RE1 OR -RE2)
.096 2.44
.1635 4.153
REF
"A" REF
(SEE TABLE 1,
SHT 7)
(SEE NOTE 8)
-SN2: SOLDER NAIL FOR .093 BOARD
(TFM-XX-D-01-SN AND WT-27-02-T)
(SEE FIG12, SHT 3)
(ONLY AVAILABLE WITH -02 LEAD STYLE)
(NOT AVAILABLE WITH OPTIONS -A, -LC,
-RA, -SA, -WT, -RE1 OR -RE2)
SEE NOTE 12
.010 0.25 REF
-DS: DUAL SCREW DOWN FOR .062 BOARD
(SEE FIG 18, SHT 5)
.014 0.36 REF
MAX SWAY
"A"
"J" ± .003 [0.08]
(SEE TABLE 1, SHT 7)
C
(ONLY AVAILABLE WITH -01 & -02 LEAD STYLE)
(NOT AVAILABLE WITH OPTIONS -A, -LC, -P,
-RA, -TR, -SA, -K, -WT, -RE1, -RE2, -SN, -SN2)
(-01 LEAD STYLE USES TFM-XX-D-01-DSL
& T1-M2-4-VSFM-T, 02 LEAD STYLE USES
TFM-XX-D-01-DSA & T1-M2-4-VSFM-T)
C
.050 1.27
2
(EITHER DIRECTION)
C
2
MAX SWAY
(EITHER DIRECTION)
SECTION "A"-"A"
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
(No OF POSITIONS x .050[1.27]) - .050[1.27]
C
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS CONFIDENTIAL AND
*
*
PROPRIETARY INFORMATION AND ALL DESIGN,
TOLERANCES ARE:
DECIMALS
MANUFACTURING, REPRODUCTION, USE, PATENT RIGHTS
AND SALES RIGHTS ARE EXPRESSLY RESERVED BY SAMTEC,
INC. THIS DOCUMENT SHALL NOT BE DISCLOSED, IN WHOLE
OR PART, TO ANY UNAUTHORIZED PERSON OR ENTITY NOR
REPRODUCED, TRANSFERRED OR INCORPORATED IN ANY
OTHER PROJECT IN ANY MANNER WITHOUT THE EXPRESS
WRITTEN CONSENT OF SAMTEC, INC.
ANGLES
2
"C"±.003 [0.08]
(SEE TABLE 1,
C
.XX: .01[0.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
FIG 1
.XXX: .005[0.13]
PHONE: 812-944-6733
e-Mail info@SAMTEC.com
FAX: 812-948-5047
code 55322
.XXXX: .0020[0.051]
THROUGH HOLE
SHT 7)
-01, -03, -11, -13, -21, -23, -31
SHEET SCALE: 2.5:1
MATERIAL:
DO NOT SCALE DRAWING
DESCRIPTION:
INSULATOR:
LCP, UL 94-VO
COLOR: BLACK
.050 X .050 TERMINAL STRIP
DWG. NO.
IN-PROCESS
TFM-1XX-XX-XXX-D-XXX
TERMINAL: PHOSPHOR BRONZE
F:\DWG\MISC\MKTG\TFM-1XX-XX-XXX-D-XXX-MKT.SLDDRW
SHEET 1 OF
7
BY: garyp
11/5/2014
5秒后页面跳转
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
AMD宣布全球裁员约1000人，调整战略聚焦增长
英伟达新AI芯片Rubin或提前半年亮相
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
技术参数
数据手册
如果您发现信息不准确，
