5秒后页面跳转
捷配首页

Datasheet > TF43SW-66S/4-0.5SH(800)
TF43SW-66S/4-0.5SH(800) PDF预览

TF43SW-66S/4-0.5SH(800)

更新时间： 2024-06-27 12:13:19
品牌 Logo 应用领域
广濑 - HRS PC连接器FFC连接器
页数 文件大小 规格书
1页 264K
描述
安装间距:0.5 mm;连接器长度(间距方向):47.88 mm;连接器高度:1.2 mm;连接器宽度(纵向):4.84 mm;接触点位置:下接点;推荐的FFC/FPC:FPC/FFC连接器;FP

阅读下载

中文翻译

获取价格

TF43SW-66S/4-0.5SH(800) 数据手册

  
COUNT  
COUNT  
CHKD  
DESCRIPTION OF REVISIONS  
RE-5-2548  
DATE  
DESCRIPTION OF REVISIONS  
DATE  
CHKD  
BY  
BY  
21.01.29  
S.J.H C.D.H  
1
△
2
△
△
△
APPLICABLE STANDARD  
OPERATING TEMPERATURE  
STORAGE TEMPERATURE  
-10℃ ~ +50℃(Packed Condition)  
-40℃ ~ +85℃  
RANGE  
RANGE  
OPERATING OR STORAGE  
HUMIDITY RANGE  
RELATIVE HUMIDITY 90%MAX(NOT DEWED)  
50V [AC(rms) / DC]  
VOLTAGE  
CURRENT  
RATING  
Signal Contact 0.5A (note1)  
Power Contact 12A(6A/Pin) (note2)  
APPLICABLE  
CABLE  
FPC / FFC  
(t=0.3±0.03, COPPER FOIL = 2oz)  
1
SPECIFICATIONS  
TEST METHOD  
ITEM  
REQUIREMENTS  
QT AT  
CONSTRUCTION  
GENERAL EXAMINATION  
VISUALLY AND BY MEASURING INSTRUMENT  
CONFIRMED VISUALLY  
O
O
O
O
ACCORDING TO DRAWING  
MARKING  
ELECTRICAL CHARACTERISTICS  
CONTACT RESISTANCE  
INSULATION RESISTANCE  
VOLTAGE PROOF  
MATE APPLICABLE FPC/FFC AND APPLY A CURRENT OF  
50 mΩ MAX.  
O
O
O
O
O
O
AC 20mV MAX, 100mA MAX  
INCLUDING FPC/FFC BULK RESISTANCE(L=8mm)  
MATE APPLICABLE FPC/FFC AND APPLY A VOLTAGE OF  
DC 100V  
500 MΩ MIN.  
MATE APPLICABLE FPC/FFC AND APPLY A VOLTAGE OF  
AC 150V FOR 1 min.  
NO FLASHOVER OR BREAKDOWN.  
MECHANICAL CHARACTERISTICS  
FPC RETENSION FORCE  
MECHANICAL OPERATION  
VIBRATION  
MEASURE BY APPLICABLE FPC/FFC  
①HORIZONTAL DIRECTION : 25N(2.5Kgf) MIN.  
②VERTICAL DIRECTION : 15N(1.5Kgf) MIN.  
①CONTACT RESISTANCE: 50mΩ MAX  
O
O
O
O
-
AT INITIAL CONDITION  
20 TIMES INSERTIONS AND EXTRATIONS  
-
-
-
②NO DAMAGE,CRACK AND LOOSENESS OF PARTS  
①NO ELECTRICAL DISCONTINUITY OF 1㎲.  
②CONTACT RESISTANCE : 50mΩ MAX  
FREQUENCY 10 ~ 55 Hz, TOTAL AMPLITUDE 1.5 mm  
AT 2h, IN 3 DIRECTIONS  
981m/s2 DIRECTION OF PULSE 6ms AT 3 TIMES  
SHOCK  
③NO DAMAGE,CRACK AND LOOSENESS OF PARTS  
IN 3 DIRECTIONS.  
ENVIRONMENTAL CHARACTERISTICS  
DAMP HEAT(STEADY STATE)  
EXPOSED AT 40±2℃, 90~95 %, 96Hr.  
①CONTACT RESISTANCE: 50 mΩ MAX.  
O
O
-
-
RAPID CHAGE OF TEMPERATURE  
TEMPERATURE : -40±2 → 15~35 → +85±2 → 15~35 ℃  
②INSULATION RESISTANCE: 50MΩ MIN.  
③NO DAMAGE, CRACK OR LOOSENESS OF PARTS.  
TIME :  
30 → 2~3 → 30 → 2~3 min.  
UNDER 5 CYCLES.  
DAMP HEAT, CYCLE  
TEMPERATURE -10→+65  
HUMIDITY : 90~95%  
O
-
10 CYCLE(240Hr)  
DRY HEAT  
EXPOSED AT 85±2℃, 96Hr  
EXPOSED AT -40±2℃, 96Hr  
①CONTACT RESISTANCE : 50mΩ MAX  
O
O
-
-
COLD  
②NO DAMAGE, CRACK OR LOOSENESS OF PARTS.  
CORROSION SALT SPRAY  
EXPOSED AT 35±2℃, 5±1% SALT WATER SPRAY FOR 48Hr ①CONTACT RESISTANCE 50mΩ MAX  
②NO DAMAGE, CRACK OR LOOSENESS OF PARTS.  
O
O
-
-
HYDROGEN SULPHIDE  
EXPOSED IN 3 PPM FOR 96Hr.  
(TEST STANDARD : JEIDA-38)  
REFLOW SOLDERING:  
③NO EVIDENCE OF CORROSION WHICH AFFECTS  
TO OPERATION OF CONNECTOR.  
RESISTANCE TO  
SOLDERING HEAT  
①NO DEFORMATION OF CASE OF EXCESSIVE  
LOOSENESS OF THE TERMINALS.  
PEAK TMP. : 250℃ MAX.  
O
O
-
-
REFLOW TMP. 230℃ MIN FOR 30s  
SOLDER DIPPING TEMPERATURE 245±5℃  
FOR IMMERSION DURATION, 3±0.3 sec.  
SOLDER ABILITY  
A NEW UNIFORM COATING OF SOLDER  
SHALL COVER A MINIMUM OF 95%  
OF THE SURFACE BEING IMMERSED.  
(note 1)  
WHEN THE SAME VALUE OF CURRENT ARE APPLID TO ALL CONTACTS AT THE SAME TIME IN ONCE,  
SET THE CURRENT TO THE 70% OF THE RATED CURRENT VALUE.  
(note 2)  
THE POWER TERMINAL IS 6A/PIN AND CAN BE USED AS 12A BY CONNECTING TWO TERMINALS IN PARALLEL.  
1
DRAWN  
J.H SEO  
19.08.28  
DESIGNED  
J.H SEO  
19.08.28  
CHECKED  
D.H CHO  
19.08.28  
APPROVED  
D.H CHO  
19.08.28  
REMARKS CONDITIONS FOR TESTING  
RELEASED  
ENG  
20.02.01  
DEPT.  
UNLESS OTHERWISE SPECIFIED, REFER TO JIS C 5402.  
NOTE QT: QUALIFICATION TEST AT: ASSURANCE TEST O: APPLICABLE TEST  
PART NO.  
HIROSE KOREA CO.,LTD.  
SPECIFICATION SHEET  
TF43SW-66S/4-0.5SH(800)  
CODE NO.(OLD)  
DRAWING NO.  
CODE NO.  
1
CL 6553-0003-5-800  
ELC4-632535-80  
CL  
1
F-1-021(Rev.0)  
1

中文翻译

下载PDF

与TF43SW-66S/4-0.5SH(800)相关器件

型号 品牌 获取价格 描述 数据表
TF440 DYNEX

获取价格

 		Fast Switching Thyristor
TF440-01A STMICROELECTRONICS

获取价格

 		SILICON CONTROLLED RECTIFIER,100V V(DRM),400A I(T),TO-200AB
TF440-01B STMICROELECTRONICS

获取价格

 		SILICON CONTROLLED RECTIFIER,100V V(DRM),400A I(T),TO-200AB
TF440-01Q STMICROELECTRONICS

获取价格

 		SILICON CONTROLLED RECTIFIER,100V V(DRM),400A I(T),TO-200AB
TF440-01W STMICROELECTRONICS

获取价格

 		SILICON CONTROLLED RECTIFIER,100V V(DRM),400A I(T),TO-200AB
TF440-01X STMICROELECTRONICS

获取价格

 		SILICON CONTROLLED RECTIFIER,100V V(DRM),400A I(T),TO-200AB
TF440-01Y STMICROELECTRONICS

获取价格

 		SILICON CONTROLLED RECTIFIER,100V V(DRM),400A I(T),TO-200AB
TF440-02Y STMICROELECTRONICS

获取价格

 		SILICON CONTROLLED RECTIFIER,200V V(DRM),400A I(T),TO-200AB
TF440-04W STMICROELECTRONICS

获取价格

 		SILICON CONTROLLED RECTIFIER,400V V(DRM),400A I(T),TO-200AB
TF440-10D STMICROELECTRONICS

获取价格

 		SILICON CONTROLLED RECTIFIER,1KV V(DRM),400A I(T),TO-220

与TF43SW-66S/4-0.5SH(800)相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证