5秒后页面跳转
捷配首页

Datasheet > TF42-16S-0.35SH(895)
TF42-16S-0.35SH(895) PDF预览

TF42-16S-0.35SH(895)

更新时间： 2024-10-15 18:09:19
品牌 Logo 应用领域
广濑 - HRS 插座连接器
页数 文件大小 规格书
1页 52K
描述
连接器类型:插座;安装间距:0.35 mm;连接器长度(间距方向):7.05 mm;连接器高度:0.9 mm;连接器宽度(纵向):3.0 mm;接触点位置:下接点;ZIF/Non-O ZIF/LI

阅读下载

中文翻译

获取价格

TF42-16S-0.35SH(895) 数据手册

  
COUNT  
COUNT  
DATE  
DATE  
DESCRIPTION OF REVISIONS  
DESCRIPTION OF REVISIONS  
REV  
BY CHKD  
REV  
BY CHKD  
APPLICABLE STANDARD  
OPERATING  
STORAGE  
-10 ℃ ~ +50 ℃  
-55 ℃ ~ +85 ℃  
30 V [AC(rms) / DC]  
TEMPERATURE RANGE  
TEMPERATURE RANGE  
(PACKED CONDITION)  
OPERATING OR STORAGE  
HUMIDITY RANGE  
RELATIVE HUMIDITY 90 % MAX  
RATING VOLTAGE  
CURRENT  
(NOT DEWED)  
APPLICABLE CABLE  
0.4 A [AC(rms) / DC] (NOTE 1)  
FPC (T=0.2 ±0.03 mm)  
SPECIFICATIONS  
ITEM  
TEST METHOD  
REQUIREMENTS  
QT AT  
CONSTRUCTION  
GENERAL EXAMINATION  
VISUALLY AND BY MEASURING INSTRUMENT  
CONFIRMED VISUALLY  
ACCORDING TO DRAWING  
O
O
O
O
MARKING  
ELECTRICAL CHARACTERISTICS  
CONTACT RESISTANCE  
INSULATION RESISTANCE  
VOLTAGE PROOF  
MATE APPLICABLE FPC/FFC AND APPLY A CURRENT OF  
100 mΩ MAX  
O
O
O
O
O
O
1 mA AC (OR 1,000 Hz)  
INCLUDING FPC/FFC BULK RESISTANCE (L=8 mm)  
500 MΩ MIN  
MATE APPLICABLE FPC/FFC AND APPLY A VOLTAGE OF  
DC 100 V  
MATE APPLICABLE FPC/FFC AND APPLY A VOLTAGE OF  
AC 150 V FOR 1 min  
NO FLASHOVER OR BREAKDOWN  
MECHANICAL CHARACTERISTICS  
FPC RETENSION FORCE  
MEASURE BY APPLICABLE FPC/FFC (T=0.2)  
① HORIZONTAL DIRECTION : 0.25 N * n MIN  
AT INITIAL CONDITION  
② VERTICAL DIRECTION : 0.25 N * n MIN  
(n : NUMBER OF CONTACTS)  
O
-
① CONTACT RESISTANCE : 100 mΩ MAX  
② NO DAMAGE, CRACK AND LOOSENESS OF PARTS  
① NO ELECTRICAL DISCONTINUITY OF 1 ㎲  
② CONTACT RESISTANCE : 100 mΩ MAX  
③ NO DAMAGE, CRACK AND LOOSENESS OF PARTS  
MECHANICAL OPERATION  
VIBRATION  
20 TIMES INSERTIONS AND EXTRATIONS  
O
O
O
-
-
-
FREQUENCY 10 ~ 55 Hz, TOTAL AMPLITUDE 1.5 mm  
AT 2 hrs, IN 3 DIRECTIONS  
981 m/s2 DIRECTION OF PULSE 6 ms AT 3 TIMES  
IN 3 DIRECTIONS  
SHOCK  
ENVIRONMENTAL CHARACTERISTICS  
DAMP HEAT (STEADY STATE)  
EXPOSED AT 40 ℃, 90~95 %, 96 hrs  
① CONTACT RESISTANCE : 100 mΩ MAX  
O
O
-
-
RAPID CHANGE OF TEMPERATURE  
→ 15~35 →+85 → 15~35 ℃  
② INSULATION RESISTANCE : 100 MΩ MIN  
③ NO DAMAGE, CRACK AND LOOSENESS OF PARTS  
TEMP. : -55  
→
30  
2~3 → 30 → 2~3 min  
TIME  
:
5 CYCLES WITH ABOVE CONDITIONS  
TEMPERATURE : -10 → +65 ℃  
HUMIDITY : 90~95 %  
DAMP HEAT, CYCLE  
O
-
10 CYCLE (240 hrs)  
DRY HEAT  
EXPOSED AT 85 ℃, 96 hrs  
① CONTACT RESISTANCE : 100 mΩ MAX  
② NO DAMAGE, CRACK AND LOOSENESS OF PARTS  
① CONTACT RESISTANCE : 100 mΩ MAX  
② NO DAMAGE, CRACK AND LOOSENESS OF PARTS  
③ NO EVIDENCE OF CORROSION WHICH AFFECTS  
TO OPERATION OF CONNECTOR  
O
O
-
-
COLD  
EXPOSED AT -55 ℃, 96 hrs  
CORROSION SALT SPRAY  
EXPOSED AT 35 ℃, 5 % SALT WATER SPRAY FOR 48 hrs  
O
O
-
-
HYDROGEN SULPHIDE  
EXPOSED IN 3 PPM FOR 96 hrs  
(TEST STANDARD : JEIDA-38)  
RESISTANCE TO SOLDERING HEAT  
REFLOW SOLDERING  
① NO DEFORMATION OF CASE OF EXCESSIVE  
LOOSENESS OF THE TERMINALS  
TEMP. : 230 ℃ MIN FOR 60 sec  
PEAK TEMP. : 250 ℃ MAX  
O
O
-
-
② NO DAMAGE OF ELECTRICAL PERFORMANCE  
A NEW UNIFORM COATING OF SLODER  
SHALL COVER A MINIMUM OF 95 % OF  
THE SURFACE BEING EMMERSED.  
SOLDERABILITY  
NOTE  
SOLDERED AT SOLDER TEMPERATURE 245 ±3 ℃  
FOR IMMERSION DURATION 3 ±0.3 sec  
1) WHEN THE SAME VALUE OF CURRENT ARE APPLIED TO ALL CONTACTS AT THE SAME TIME IN ONCE,  
SET THE CURRENT TO THE 70 % OF THE RATED CURRENT VALUE.  
RELEASED  
REMARKS  
CONDITIONS FOR TESTING  
DRAWN  
DESIGNED  
CHECKED  
APPROVED  
DEPT  
21.02.16  
ENG  
J.H.BOO  
21.02.16  
J.H.BOO D.H.CHO D.H.CHO  
21.02.16 21.02.16 21.02.16  
UNLESS OTHERWISE SPECIFIED, REFER TO IEC 60512  
NOTE QT: QUALIFICATION TEST AT: ASSURANCE TEST O: APPLICABLE TEST  
PART NO.  
HIROSE KOREA CO.,LTD.  
SPECIFICATION SHEET  
TF42-**S-0.35SH(895)  
CODE NO. (OLD)  
DRAWING NO.  
CODE NO.  
1
ELC4-633304-95  
CL ****-****-*-***  
1
F-1-021(Rev.0)  
1

中文翻译

下载PDF

与TF42-16S-0.35SH(895)相关器件

型号 品牌 获取价格 描述 数据表
TF42-22S-0.35SH(800) HRS

获取价格

 		Headers and Edge Type Connector,
TF42-22S-0.35SH(895) HRS

获取价格

 		连接器类型:插座;安装间距:0.35 mm;连接器长度(间距方向):9.15 mm;连接器
TF42-24S-0.35SH(800) HRS

获取价格

 		Headers and Edge Type Connector,
TF42-24S-0.35SH(895) HRS

获取价格

 		连接器类型:插座;安装间距:0.35 mm;连接器长度(间距方向):9.85 mm;连接器
TF4-27027015% VISHAY

获取价格

 		General Purpose Inductor, 270uH, 15%, 1 Element
TF4-272715% VISHAY

获取价格

 		General Purpose Inductor, 27uH, 15%, 1 Element
TF4-33033015% VISHAY

获取价格

 		General Purpose Inductor, 330uH, 15%, 1 Element
TF4-333315% VISHAY

获取价格

 		General Purpose Inductor, 33uH, 15%, 1 Element
TF4333TU TDK

获取价格

 		Common Mode Choke Coils Line Filters for AC Power Supply Toroidal Core Type
TF4333TU-302Y7R0-01 TDK

获取价格

 		Three Phase EMI Filter, 280V,

与TF42-16S-0.35SH(895)相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证