COUNT
COUNT
CHKD
DESCRIPTION OF REVISIONS
RE-5-2033
CHKD DATE
DESCRIPTION OF REVISIONS
DATE
BY
BY
18.10.04
8
1
Y.K.G C.D.H
△
△
1
2
RE-5-2988
23.04.24
C.Y.H C.D.H
APPLICABLE STANDARD
OPERATING TEMPERATURE
RANGE
STORAGE TEMPERATURE
RANGE
-10℃~+50℃(Packed Condition)
-40℃ ~ +105℃ (note1)
50V [AC(rms) / DC]
1
OPERATING OR STORAGE
HUMIDITY RANGE
Relative Humidity
90% MAX(NOT DEWED)
RATING
VOLTAGE
CURRENT
APPLICABLE
CABLE
1
FPC/FFC (t=0.3±0.03mm)
0.5A [AC(rms) / DC] (note 2)
SPECIFICATIONS
ITEM
TEST METHOD
REQUIREMENTS
QT AT
CONSTRUCTION
GENERAL EXAMINATION
MARKING
VISUALLY AND BY MEASURING INSTRUMENT
CONFIRMED VISUALLY
ACCORDING TO DRAWING
O
O
ELECTRICAL CHARACTERISTICS
CONTACT RESISTANCE
INSULATION RESISTANCE
VOLTAGE PROOF
MATE APPLICABLE FPC/FFC AND APPLY A CURRENT OF
AC 20mV MAX (1KHz), 1mA.
50mΩ MAX.
O
O
O
O
O
O
INCLUDING FPC/FFC BULK RESISTANCE(L=8mm)
MATE APPLICABLE FPC/FFC AND APPLY A VOLTAGE OF DC 500MΩ MIN.
100V.
MATE APPLICABLE FPC/FFC AND APPLY A VOLTAGE OF
AC 150V FOR 1 min.
NO BREAKDOWN
2
MECHANICAL CHARACTERISTICS
MECHANICAL OPERATION
20 TIMES INSERTIONS AND EXTRATIONS.
① CONTACT RESISTANCE : 50mΩ MAX.
O
O
O
-
-
-
② NO DAMAGE,CRACK AND LOOSENESS OF PARTS
VIBRATION
FREQUENCY 10 TO 55 Hz, HALF AMPLITUDE
① NO ELECTRICAL DISCONTINUITY OF 1㎲.
② CONTACT RESISTANCE : 50mΩ MAX.
③ NO DAMAGE,CRACK AND LOOSENESS OF PARTS
0.75 mm, - m/s2 FOR 10 CYCLES IN 3 DIRECTIONS.
981m/s2 DIRECTION OF PULSE 6ms AT 3 TIMES
IN 3 DIRECTIONS.
SHOCK
FPC/FFC RETENSION FORCE
MEASURE BY APPLICABLE FPC/FFC.
(THICKNESS OF FPC/FFC SHALL BE t=0.30mm
AT INITIAL CONDITION.)
HORIZONTAL DIRECTION : 0.3N X n MIN.
1
O
-
(n : NUMBER OF CONTACTS). (note 3)
ENVIRONMENTAL CHARACTERISTICS
TEMPERATURE : -40 → 15 TO 35 → +105 → 15 TO 35 ℃
① CONTACT RESISTANCE : 50mΩ MAX.
② INSULATION RESISTANCE : 50MΩ MIN.
③ NO DAMAGE, CRACK OR LOOSENESS OF PARTS
RAPID CHANGE OF TEMPERATURE 1
TIME : 30 → 2~3 → 30 → 2~3 min
UNDER 5 CYCLES.
O
O
O
-
-
-
DAMP HEAT (STEADY STATE)
DAMP HEAT, CYCLE
EXPOSED AT 40±2℃, 90~95 %, 96h.
TEMPERATURE : -10 TO +65℃
HUMIDITY : 90 TO 95%
10 CYCLE, TOTAL 240h.
DRY HEAT
EXPOSED AT 105±2℃, 96h.
① CONTACT RESISTANCE : 50mΩ MAX.
② NO DAMAGE, CRACK OR LOOSENESS OF PARTS
O
O
O
-
-
-
1
COLD
EXPOSED AT -40±3℃, 96h.
CORROSION SALT MIST
SURPHUR DIOXIDE
[JIS C 0090]
EXPOSED AT 35±2℃, 5% SALT WATER SPRAY FOR 96h.
EXPOSED AT 40±2℃, RELATIVE HUMIDITY
80±5%, 25±5 PPM FOR 96h.
① CONTACT RESISTANCE : 50mΩ MAX.
② NO EVIDENCE OF CORROSION WHICH AFFECTS
TO OPERATION OF CONNECTOR
O
-
HYDROGEN SULPHIDE
[JIS C 0092]
EXPOSED AT 40±2℃, RELATIVE HUMIDITY
80±5%, 10 TO 15 PPM FOR 96h.
O
-
RESISTANCE TO SOLDERING HEAT
1) REFLOW SOLDERING :
PEAK TMP. 250℃ MAX.
① NO DEFORMATION OF CASE OF EXCESSIVE
LOOSENESS OF THE TERMINALS
REFLOW TMP.230℃ MIN. FOR 60 sec.
2) SOLDERING IRONS :
TMP. 350±5℃ FOR 5±1 sec.
② NO DAMAGE OF ELECTRICAL PERFORMANCE
O
O
-
-
SOLDERABILITY
SOLDER DIPPING TEMPERATURE 245±5℃,
FOR IMMERSION DURATION, 3±0.3 sec.
A NEW UNIFORM COATING OF SOLDER
SHALL COVER A MINIMUM OF 95% OF
THE SURFACR BEING IMMERSED.
1
(note 1)
FOLLOW THE SPECIFICATIONS OF FPC/FFC IF IT’S ALLOWABLE MAXIMUM OPERATING TEMPERATURE
IS BELOW 105℃
1
1
(note 2)
WHEN THE SAME VALUE OF CURRENT ARE APPLIED TO ALL CONTACTS AT THE SAME TIME IN ONCE,
SET THE CURRENT TO THE 70% OF THE RATED CURRENT VALUE.
(note 3)
THERE’S A CASE WHICH FPC/FFC RETENTION FORCE DOESN’T FULFILL THE VALUE,
BECAUSE FPC/FFC SPECIFICATION AFFECTS THE RESULT OF FPC/FFC RETENTION FORCE.
RELEASED
DRAWN
DESIGNED
CHECKED
APPROVED
REMARKS
ENG
23.04.24
DEPT
B.J KIM
B.J KIM
D.H CHO H.C SONG
18.03.02 18.03.02
18.03.02
18.03.02
UNLESS OTHERWISE SPECIFIED, REFER TO JIS C 5402.
NOTE QT: QUALIFICATION TEST AT: ASSURANCE TEST O: APPLICABLE TEST
PART NO.
HIROSE KOREA CO.,LTD.
SPECIFICATION SHEET
TF38-**S-0.5SV(830)
CL 6537-****-*-830
CODE NO.(OLD)
DRAWING NO.
CODE NO.
1
ELC4-632306
CL
1
F-1-021(Rev.0)
5秒后页面跳转
SL74HC10N：高性能三输入与非门解析
AIC1781A 电池充电控制器深度解析
Pickering新高压舌簧继电器亮相汽车测试博览会
采用MCU+MPU双处理器架构实现的创新应用设计探索
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
