5秒后页面跳转
捷配首页

Datasheet > TF31-10S-0.5SH(800)
TF31-10S-0.5SH(800) PDF预览

TF31-10S-0.5SH(800)

更新时间： 2024-06-27 12:10:45
品牌 Logo 应用领域
广濑 - HRS 插座连接器
页数 文件大小 规格书
1页 248K
描述
连接器类型:插座;安装间距:0.5 mm;连接器长度(间距方向):9.3 mm;连接器高度:1.75 mm;连接器宽度(纵向):5.7 mm;接触点位置:下接点;ZIF/Non-O ZIF/LIF

阅读下载

中文翻译

获取价格

TF31-10S-0.5SH(800) 数据手册

  
COUNT  
COUNT  
CHKD  
DESCRIPTION OF REVISIONS  
RE-5-2033  
CHKD DATE  
DESCRIPTION OF REVISIONS  
DATE  
BY  
BY  
18.10.04  
8
1
Y.K.G C.D.H  
△
△
1
2
RE-5-2988  
23.04.24  
C.Y.H C.D.H  
APPLICABLE STANDARD  
OPERATING TEMPERATURE  
RANGE  
STORAGE TEMPERATURE RANGE  
-10℃ ~ +50℃(Packed Condition)  
-40℃ ~ +105℃ (note1)  
50V [AC(rms) / DC]  
1
1
OPERATING OR STORAGE  
HUMIDITY RANGE  
RELATIVE HUMIDITY 90% MAX (NOT DEWED)  
VOLTAGE  
CURRENT  
RATING  
FPC/FFC (TYPE A : t=0.3±0.03mm)  
(TYPE B : t=0.3±0.05mm)  
0.5A [AC(rms) / DC] (note2)  
APPLICABLE CABLE  
SPECIFICATIONS  
ITEM  
TEST METHOD  
REQUIREMENTS  
QT AT  
CONSTRUCTION  
GENERAL EXAMINATION  
VISUALLY AND BY MEASURING INSTRUMENT  
CONFIRMED VISUALLY  
O
O
O
O
ACCORDING TO DRAWING  
MARKING  
ELECTRICAL CHARACTERISTICS  
CONTACT RESISTANCE  
INSULATION RESISTANCE  
VOLTAGE PROOF  
MATE APPLICABLE FPC/FFC AND APPLY A CURRENT OF  
50 mΩ MAX.  
O
O
O
O
O
O
AC 20mV MAX, 1mA  
INCLUDING FPC/FFC BULK RESISTANCE(L=8mm)  
500 MΩ MIN.  
MATE APPLICABLE FPC/FFC AND APPLY A VOLTAGE OF  
DC 100V  
MATE APPLICABLE FPC/FFC AND APPLY A VOLTAGE OF  
AC 150V FOR 1 min.  
NO BREAKDOWN.  
2
MECHANICAL CHARACTERISTICS  
FPC RETENSION FORCE  
MEASURE BY APPLICABLE FPC/FFC(t=0.3)  
①HORIZONTAL DIRECTION : 0.4N*n min.  
②VERTICAL DIRECTION : 0.3N*n min.  
1
AT INITIAL CONDITION  
O
-
(n = Number of Contacts)(note 3)  
MECHANICAL OPERATION  
VIBRATION  
20 TIMES INSERTIONS AND EXTRATIONS  
①CONTACT RESISTANCE: 50mΩ MAX  
O
O
O
-
-
-
②NO DAMAGE,CRACK AND LOOSENESS OF PARTS  
①NO ELECTRICAL DISCONTINUITY OF 1㎲.  
②CONTACT RESISTANCE : 50mΩ MAX  
③NO DAMAGE,CRACK AND LOOSENESS OF PARTS  
FREQUENCY 10 ~ 55 Hz, TOTAL AMPLITUDE 1.5 mm  
AT 2h, IN 3 DIRECTIONS  
981m/s2 DIRECTION OF PULSE 6ms AT 3 TIMES  
IN 3 DIRECTIONS.  
SHOCK  
ENVIRONMENTAL CHARACTERISTICS  
DAMP HEAT(STEADY STATE)  
EXPOSED AT 40±2℃, 90~95 %, 96Hr.  
①CONTACT RESISTANCE: 50 mΩ MAX.  
O
O
-
-
RAPID CHANGE OF TEMPERATURE  
TEMPERATURE:-40±2→15~35→+105±2→15~35 ℃  
②INSULATION RESISTANCE: 50MΩ MIN.  
③NO DAMAGE, CRACK OR LOOSENESS OF PARTS.  
1
TIME :  
30 → 2~3 →  
30 → 2~3 min.  
UNDER 5 CYCLES.  
DAMP HEAT, CYCLE  
TEMPERATURE -10→+65  
HUMIDITY : 90~95%  
O
-
10 CYCLE(240Hr)  
DRY HEAT  
EXPOSED AT 105±2℃, 96Hr  
EXPOSED AT -40±2℃, 96Hr  
①CONTACT RESISTANCE : 50mΩ MAX  
②NO DAMAGE, CRACK OR LOOSENESS OF PARTS.  
①CONTACT RESISTANCE 50mΩ MAX  
O
O
-
-
1
COLD  
CORROSION SALT SPRAY  
EXPOSED AT 35±2℃, 5±1% SALT WATER SPRAY FOR 48Hr  
O
O
-
②NO DAMAGE, CRACK OR LOOSENESS OF PARTS.  
③NO EVIDENCE OF CORROSION WHICH AFFECTS  
TO OPERATION OF CONNECTOR.  
HYDROGEN SULPHIDE  
EXPOSED IN 3 PPM FOR 96Hr.  
-
(TEST STANDARD : JEIDA-38)  
RESISTANCE TO  
1)REFLOW SOLDERING:  
①NO DEFORMATION OF CASE OF EXCESSIVE  
LOOSENESS OF THE TERMINALS.  
SOLDERING HEAT  
PEAK TMP. : 250℃ MAX. TMP. 230℃ MIN FOR 60s  
2)SOLDERING IRONS TMP. : 350±10℃ FOR 5±1s  
SOLDER DIPPING TEMPERATURE 245±5℃  
(TEST STANDARD : MIL-STD-202)  
O
O
-
-
②NO DAMAGE OF ELECTRICAL PERFORMANCE  
A NEW UNIFORM COATING OF SOLDER  
SHALL COVER A MINIMUM OF 95% OF  
THE SURFACE BEING IMMERSED.  
SOLDER ABILITY  
FOR IMMERSION DURATION, 3±0.3 sec.  
(note 1)  
1
FOLLOW THE SPECIFICATIONS OF FPC/FFC IF IT’S ALLOWABLE MAXIMUM OPERATING TEMPERATURE  
IS BELOW 105℃  
(note 2)  
1
WHEN THE SAME VALUE OF CURRENT ARE APPLIED TO ALL CONTACTS AT THE SAME TIME IN ONCE,  
SET THE CURRENT TO THE 70% OF THE RATED CURRENT VALUE.  
1
(note 3)  
THERE’S A CASE WHICH FPC/FFC RETENTION FORCE DOESN’T FULFILL THE VALUE,  
BECAUSE FPC/FFC SPECIFICATION AFFECTS THE RESULT OF FPC/FFC RETENTION FORCE.  
RELEASED  
DRAWN  
DESIGNED  
CHECKED  
APPROVED  
REMARKS CONDITIONS FOR TESTING  
B.J KIM  
B.J KIM  
D.H CHO H.C SONG  
18.03.02  
18.03.02  
18.03.02 18.03.02  
UNLESS OTHERWISE SPECIFIED, REFER TO JIS C 5402.  
NOTE QT: QUALIFICATION TEST AT: ASSURANCE TEST O: APPLICABLE TEST  
PART NO.  
HIROSE KOREA CO.,LTD.  
SPECIFICATION SHEET  
TF31-**S-0.5SH (800)  
CODE NO.(OLD)  
DRAWING NO.  
CODE NO.  
1
CL 6535-****-*-800  
ELC4-632346  
CL  
1
F-1-021(Rev.0)  
1

中文翻译

下载PDF

与TF31-10S-0.5SH(800)相关器件

型号 品牌 获取价格 描述 数据表
TF31-10S-0.5SH(895) HRS

获取价格

 		连接器类型:插座;安装间距:0.5 mm;连接器长度(间距方向):9.3 mm;连接器高度
TF31-10S-1SH(800) HRS

获取价格

 		连接器类型:插座;安装间距:1.0 mm;连接器长度(间距方向):14.8 mm;连接器高
TF31-12S-0.5SH(800) HRS

获取价格

 		连接器类型:插座;安装间距:0.5 mm;连接器长度(间距方向):10.3 mm;连接器高
TF31-12S-0.5SH(895) HRS

获取价格

 		连接器类型:插座;安装间距:0.5 mm;连接器长度(间距方向):10.3 mm;连接器高
TF31-13S-0.5SH(800) HRS

获取价格

 		连接器类型:插座;安装间距:0.5 mm;连接器长度(间距方向):10.8 mm;连接器高
TF31-13S-0.5SH(895) HRS

获取价格

 		连接器类型:插座;安装间距:0.5 mm;连接器长度(间距方向):10.8 mm;连接器高
TF31-14S-0.5SH(800) HRS

获取价格

 		连接器类型:插座;安装间距:0.5 mm;连接器长度(间距方向):11.3 mm;连接器高
TF31-14S-0.5SH(895) HRS

获取价格

 		连接器类型:插座;安装间距:0.5 mm;连接器长度(间距方向):11.3 mm;连接器高
TF31-16S-0.5SH(800) HRS

获取价格

 		连接器类型:插座;安装间距:0.5 mm;连接器长度(间距方向):12.3 mm;连接器高
TF31-16S-0.5SH(895) HRS

获取价格

 		连接器类型:插座;安装间距:0.5 mm;连接器长度(间距方向):12.3 mm;连接器高

与TF31-10S-0.5SH(800)相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证