TAC5412-Q1
SLASF33 – JANUARY 2024
TAC5412-Q1 Automotive Low Power Stereo Audio Codec with integrated
programmable boost, micbias and diagnostics
•
•
•
Telematics Control Unit
Automotive active noise cancellation
Automotive head units
1 Features
•
AEC-Q100 qualified for automotive applications
– Temperature grade 1: –40°C ≤ TA ≤ +125°C
3 Description
•
ADC Channel
– Performance:
The TAC5412-Q1 is a high performance Stereo
Codec with 10VRMS differential Input, 108dB Stereo
ADC and 2VRMS Stereo DAC Channels. The
TAC5412-Q1 supports both differential and Single
Ended input and output. Device supports both
Microphone and Line In input on ADC Channel.
DAC Output can be configured for either Line Out
or Head Phone Load. TAC5412-Q1 can drive up
to 62.5mW into a Headphone Load. The device
also offers an integrated high-voltage, programmable
microphone bias, and input diagnostic circuitry
that allows direct connection to microphone-based
automotive systems with full fault diagnostic capability
for direct-coupled inputs. The TAC5412-Q1 integrates
an efficient boost converter to generate a high voltage
microphone bias using an external, low-voltage,
3.3V supply, The device can also directly use an
external high-voltage supply (HVDD), which is a
readily available supply in the system to generate
the high-voltage, programmable microphone bias.
The TAC5412-Q1 integrates programable channel
gain, digital volume control, a low-jitter phase-locked
loop (PLL), a programmable high-pass filter (HPF),
programmable EQ and biquad filters, low-latency filter
modes. It allows for sample rates up to 768kHz.
The TAC5412-Q1 supports time-division multiplexing
(TDM), I2S, or left-justified (LJ) audio formats, and
can be controlled with I2C. These integrated high-
performance features, along with a single, 3.3V
supply operation, makes TAC5412-Q1 an excellent
choice for space-constrained automotive systems.
•
•
•
•
Line differential input dynamic range: 108dB
Mic differential input dynamic range: 108dB
THD+N: –95dB
Channel summing mode supports high SNR
– Input voltage:
•
•
Differential, 10-VRMS full-scale inputs
Single-ended, 5-VRMS full-scale inputs
– Sample rate (fS) = 8kHz to 768kHz
– Programmable microphone bias (5V to 10V):
•
With an integrated efficient boost converter,
or
•
With external high voltage HVDD supply
– Programmable microphone input fault
diagnostics:
•
•
•
Open inputs or shorted inputs
Short to ground, MICBIAS or VBAT
Microphone bias over current protection
•
DAC Channel
– DAC performance:
•
•
•
DAC to Line Out Dynamic Range: 119dB
DAC to HP Out Dynamic Range: 115dB
THD+N: –95dB
– Head Phone/Line Out output voltage:
•
•
Differential, 2-VRMS full-scale
Single-ended, 1-VRMS full-scale
– DAC sample Rates (fs) = 8KHz to 768KHz
Common Features
– Low Latency Filter Selection
– Programmable HPF and Biquad Filters
– I2C Control Interface
•
Device Information
PART NUMBER
PACKAGE(1)
WQFN (28)
WQFN (32)
PACKAGE SIZE(2)
4.0mm × 4.0mm
5.0mm × 5.0mm
– Audio Serial Interface
TAC5412-Q1
•
•
Format: TDM, I2S or Left Justified
Word Length: 16,20,24 or 32 Bits
– Programmable PLL for Flexible Clocking
– Single Supply Operation: 3.3V
– I/O Supply Operation: 1.2V, 1.8V or 3.3V
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
(2) The package size (length × width) is a nominal value and
includes pins, where applicable.
2 Applications
•
Emergency Call- E-Call
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. ADVANCE INFORMATION for preproduction products; subject to change
without notice.