ST7MC1/ST7MC2
8-bit MCU with nested interrupts, flash, 10-bit ADC,
brushless motor control, five timers, SPI, LINSCI™
Features
■ Memories
– 8K to 60K dual voltage FLASH Program mem-
ory or ROM with read-out protection capabili-
ty, In-Application Programming and In-Circuit
Programming.
LQFP64
14 x 14
LQFP44
10 x 10
LQFP80
14 x 14
– 384 to 1.5K RAM
– HDFlash endurance: 100 cycles, data reten-
tion: 40 years at 85°C
SDIP32
LQFP32 7x 7
■ Clock, reset and supply management
– Enhanced reset system
– Enhanced low voltage supervisor (LVD) for
main supply and auxiliary voltage detector
(AVD) with interrupt capability
– Clock sources: crystal/ceramic resonator os-
cillators and by-pass for external clock, clock
security system.
■ 2 Communication interfaces
– SPI synchronous serial interface
– LINSCI™ asynchronous serial interface
■ Brushless motor control peripheral
– 6 high sink PWM output channels for sine-
wave or trapezoidal inverter control
– Four power saving modes: Halt, Active-Halt,
– Motor safety including asynchronous emer-
Wait and Slow
gency stop and write-once registers
■ Interrupt management
– 4 analog inputs for rotor position detection
(sensorless/hall/tacho/encoder)
– Permanent magnet motor coprocessor includ-
ing multiplier, programmable filters, blanking
windows and event counters
– Nested interrupt controller
– 14 interrupt vectors plus TRAP and RESET
– MCES top level interrupt pin
– 16 external interrupt lines (on 3 vectors)
■ Up to 60 I/O ports
– Operational amplifier and comparator for cur-
– up to 60 multifunctional bidirectional I/O lines
rent/voltage mode regulation and limitation
– up to 41 alternate function lines
– up to 12 high sink outputs
■ Analog peripheral
– 10-bit ADC with 16 input pins
■ In-circuit Debug
■ 5 Timers
– Main Clock Controller with: Real time base,
■ Instruction set
Beep and Clock-out capabilities
– Configurable window watchdog timer
– Two 16-bit timers with: 2 input captures, 2 out-
put compares, external clock input, PWM and
pulse generator modes
– 8-bit Data Manipulation
– 63 Basic Instructions with illegal opcode de-
tection
– 17 main Addressing Modes
– 8 x 8 Unsigned Multiply Instruction
– True Bit Manipulation
– 8-bit PWM Auto-Reload timer with: 2 input
captures, 4 PWM outputs, output compare
and time base interrupt, external clock with
event detector
■ Development tools
– Full hardware/software development package
Table 1. Device Summary
Features
Program memory - bytes
RAM (stack) - bytes
ST7MC1
16K
768 (256) 1024 (256) 768 (256)
ST7MC2
32K
8K
32K
16K
48K
60K
384 (256)
1024 (256)
1536 (256)
Watchdog, 16-bit Timer A, LINSCI™, 10-bit ADC, MTC, 8-bit PWM ART, ICD
Peripherals
SPI, 16-bit Timer B
-
Operating
Supply vs. Frequency
4.5 to 5.5V with f
≤8MHz
CPU
-40°C to +85°C
/-40°C to +125°C
-40°C to
+125°C
-40°C to +85°C
-40°C to +125°C
Temperature Range
-40°C to +85°C
SDIP32
-40°C to +85 °C
1)
Package
LQFP32
LQFP32
LQFP44
SDIP56 /LQFP64 LQFP64/44 LQFP80
Note 1: For development only. No production
Rev 11
1/308
1
December 2006