Series
SRU7805W
Ultra-Wide Input, 0.5A
Non-isolated POL
Switching Regulators
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Output
Parameter
Output Voltage Accuracy
Line Regulation
Conditions
VIN = Min to Max
Min.
Typ.
±±.0
±0.ꢁ
±0.ꢀ
±0
Max.
±ꢀ.0
±ꢂ.0
±0.ꢃ
ꢃ0
Units
%
%
%
mV P - P
°C
mA
%/°C
µF
mA
W
Key Features:
• Efficiency to 95%
• Ultra-Wide Input Range
• 0.5A Output Current
• Compact SIP Case
• LM78xx Replacement
• Short Circuit Protected
• Thermal Shutdown
• Low Noise
Load Regulation
Ripple & Noise (±0 MHz)
Thermal Shutdown
Quiescent Current
Temperature Coefficient
Maximum Capacitive Load
Output Current Limit
Short Circuit Input Power
Output Short Circuit
General
IOUT = ꢂ0% to ꢂ00%
See Note ꢀ
See Note ꢁ
ꢂꢃ0
ꢂ
5
0.0ꢂ5
ꢂ00
ꢂ,±00
ꢂ.±
See Note 5
700
0.7±
Continuous (Autorecovery)
• Low Low Cost
Parameter
Conditions
Min.
Not Isolated
ꢂ±0
Typ.
Max.
Units
Isolation Voltage
Switching Frequency
Environmental
Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Lead Temperature
Cooling
800
kHz
Conditions
Min.
-ꢁ0
Typ.
+±5
Max.
+85
+ꢂ00
+ꢂ±5
ꢀ00
Units
°C
°C
°C
°C
Ambient
Case
-55
ꢂ.5 mm From Case For ꢂ0 Sec
Free Air Convection
RH, Non-condensing
Humidity
95
%
Physical
Case Size
Case Material
Weight
0.ꢁ5 x 0.ꢀ5 x 0.ꢃ9 Inches (ꢂꢂ.5 x 9.0 x ꢂ7.50 mm)
Non-Conductive Black Plastic (UL-9ꢁV0)
0.ꢂꢀ Oz (ꢀ.7g)
Reliability Specifications
Parameter
Conditions
MIL HDBK ±ꢂ7F, ±5°C, Gnd Benign
MIL HDBK ±ꢂ7F, 7ꢂ°C, Gnd Benign
Min.
ꢀ.5
ꢂ.5
Typ.
Max.
Units
MTBF
MHours
Typical Application Circuit
MicroPower Direct
±9± Page Street
Suite D
Stoughton, MA 0±07±
USA
T: (78ꢂ) ꢀꢁꢁ-8±±ꢃ
F: (78ꢂ) ꢀꢁꢁ-8ꢁ8ꢂ
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
Notes:
1. The diode D1 is used to protect the module against a reverse connection.
2. C1 is required if a high voltage input to the regulator is used. It will help prevent voltage spikes that could possibly damage
the regulator. If used, the value should be 47 µF minimum
2. This circuit example shows a simple connection utilizing a second regulator to provide a second regulated output. For
information on other circuits (filtering, protection, etc.) please contact the factory.
www.micropowerdirect.com