SN74AVCB324245
32-BIT DUAL-SUPPLY BUS TRANSCEIVER
WITH CONFIGURABLE VOLTAGE TRANSLATION AND 3-STATE OUTPUTS
www.ti.com
SCES485A–AUGUST 2003–REVISED MARCH 2005
FEATURES
•
Inputs/Outputs Can Tolerate up to 4.6 V,
Which Allows Mixed-Voltage-Mode Data
Communications
•
Member of the Texas Instruments Widebus+™
Family
•
•
Ioff Supports Partial-Power-Down Mode
Operation
•
DOC™ Circuitry Dynamically Changes Output
Impedance, Resulting in Noise Reduction
Without Speed Degradation
Fully Configurable Dual-Rail Design Allows
Each Port to Operate Over the Full 1.4-V to
3.6-V Power-Supply Range
•
Dynamic Drive Capability Is Equivalent to
Standard Outputs With IOH and IOL of
•
•
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
– ±24 mA at 3-V VCC
– ±15 mA at 2.3-V VCC
– ±9 mA at 1.65-V VCC
– ±6 mA at 1.4-V VCC
ESD Protection Exceeds JESD 22
– 2000-V Human-Body Model (A114-A)
– 200-V Machine Model (A115-A)
•
•
Control Inputs VIH/VIL Levels Are Referenced
to VCCB Voltage
– 1000-V Charged-Device Model (C101)
If Either VCC Input Is at GND, Both Ports Are in
the High-Impedance State
DESCRIPTION/ORDERING INFORMATION
This 32-bit noninverting bus transceiver uses two separate configurable power-supply rails. The A port is
designed to track VCCA. VCCA accepts any supply voltage from 1.4 V to 3.6 V. The B port is designed to track
VCCB. VCCB accepts any supply voltage from 1.4 V to 3.6 V. This allows for universal low-voltage bidirectional
translation between any of the 1.5-V, 1.8-V, 2.5-V, and 3.3-V voltage nodes.
The SN74AVCB324245 is designed for asynchronous communication between data buses. The device transmits
data from the A bus to the B bus or from the B bus to the A bus, depending on the logic level at the
direction-control (DIR) input. The output-enable (OE) input can be used to disable the outputs so the buses are
effectively isolated.
The SN74AVCB324245 is designed so that the control pins (1DIR, 2DIR, 1OE, and 2OE) are supplied by VCCB
.
To ensure the high-impedance state during power up or power down, OE shall be tied to VCCB through a pullup
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs,
preventing damaging current backflow through the device when it is powered down. If either VCC input is at GND,
both ports are in the high-impedance state.
ORDERING INFORMATION
TA
PACKAGE(1)
ORDERABLE PART NUMBER
SN74AVCB324245KR
TOP-SIDE MARKING
WD4245
LFBGA – GKE
LFBGA – ZKE (Pb-free)
–40°C to 85°C
Tape and reel
74AVCB324245ZKER
(1) Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at
www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Widebus+, DOC are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Copyright © 2003–2005, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.