5秒后页面跳转
捷配首页

Datasheet > 逻辑 > 总线驱动器/收发器> SN74AHCT16374DLR
SN74AHCT16374DLR PDF预览

SN74AHCT16374DLR

更新时间： 2024-11-04 05:29:35
品牌 Logo 应用领域
德州仪器 - TI 总线驱动器总线收发器触发器逻辑集成电路光电二极管输出元件
页数 文件大小 规格书
13页 378K
描述
16-BIT EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS

阅读下载

中文翻译

获取价格

SN74AHCT16374DLR 技术参数

是否无铅： 不含铅是否Rohs认证： 符合
生命周期：Active零件包装代码：SSOP
包装说明：SSOP, SSOP48,.4针数：48
Reach Compliance Code：compliantECCN代码：EAR99
HTS代码：8542.39.00.01风险等级：1.34
Is Samacsys：N控制类型：INDEPENDENT CONTROL
计数方向：UNIDIRECTIONAL系列：AHCT/VHCT/VT
JESD-30 代码：R-PDSO-G48JESD-609代码：e4
长度：15.88 mm负载电容（CL）：50 pF
逻辑集成电路类型：BUS DRIVER最大频率@ Nom-Sup：75000000 Hz
最大I（ol）：0.008 A湿度敏感等级：1
位数：8功能数量：2
端口数量：2端子数量：48
最高工作温度：85 °C最低工作温度：-40 °C
输出特性：3-STATE输出极性：TRUE
封装主体材料：PLASTIC/EPOXY封装代码：SSOP
封装等效代码：SSOP48,.4封装形状：RECTANGULAR
封装形式：SMALL OUTLINE, SHRINK PITCH包装方法：TR
峰值回流温度（摄氏度）：260电源：5 V
最大电源电流（ICC）：0.04 mAProp。Delay @ Nom-Sup：11.5 ns
传播延迟（tpd）：11.5 ns认证状态：Not Qualified
座面最大高度：2.79 mm子类别：FF/Latches
最大供电电压 (Vsup)：5.5 V最小供电电压 (Vsup)：4.5 V
标称供电电压 (Vsup)：5 V表面贴装：YES
技术：CMOS温度等级：INDUSTRIAL
端子面层：Nickel/Palladium/Gold (Ni/Pd/Au)端子形式：GULL WING
端子节距：0.635 mm端子位置：DUAL
处于峰值回流温度下的最长时间：NOT SPECIFIED翻译：N/A
触发器类型：POSITIVE EDGE宽度：7.49 mm
Base Number Matches：1

SN74AHCT16374DLR 数据手册

 浏览型号SN74AHCT16374DLR的Datasheet PDF文件第2页浏览型号SN74AHCT16374DLR的Datasheet PDF文件第3页浏览型号SN74AHCT16374DLR的Datasheet PDF文件第4页浏览型号SN74AHCT16374DLR的Datasheet PDF文件第5页浏览型号SN74AHCT16374DLR的Datasheet PDF文件第6页浏览型号SN74AHCT16374DLR的Datasheet PDF文件第7页 
SN54AHCT16374, SN74AHCT16374  
16-BIT EDGE-TRIGGERED D-TYPE FLIP-FLOPS  
WITH 3-STATE OUTPUTS  
SCLS337I – MARCH 1996 – REVISED FEBRUARY 2000  
SN54AHCT16374 . . . WD PACKAGE  
SN74AHCT16374 . . . DGG, DGV, OR DL PACKAGE  
(TOP VIEW)  
Members of the Texas Instruments  
Widebus Family  
EPIC (Enhanced-Performance Implanted  
CMOS) Process  
1OE  
1Q1  
1Q2  
GND  
1Q3  
1Q4  
1CLK  
1
2
3
4
5
6
7
8
9
48  
Inputs Are TTL-Voltage Compatible  
47 1D1  
46 1D2  
45 GND  
44 1D3  
43 1D4  
Distributed V  
High-Speed Switching Noise  
and GND Pins Minimize  
CC  
Flow-Through Architecture Optimizes PCB  
Layout  
V
42  
V
CC  
CC  
Latch-Up Performance Exceeds 250 mA Per  
JESD 17  
1Q5  
1Q6  
41 1D5  
40 1D6  
39 GND  
38 1D7  
37 1D8  
36 2D1  
35 2D2  
34 GND  
33 2D3  
32 2D4  
ESD Protection Exceeds 2000 V Per  
MIL-STD-883, Method 3015; Exceeds 200 V  
Using Machine Model (C = 200 pF, R = 0)  
GND 10  
1Q7 11  
1Q8 12  
2Q1 13  
2Q2 14  
GND 15  
2Q3 16  
2Q4 17  
Package Options Include Plastic Shrink  
Small-Outline (DL), Thin Shrink  
Small-Outline (DGG), and Thin Very  
Small-Outline (DGV) Packages and 380-mil  
Fine-Pitch Ceramic Flat (WD) Package  
Using 25-mil Center-to-Center Spacings  
V
18  
31  
V
CC  
CC  
2Q5 19  
2Q6 20  
GND 21  
2Q7 22  
2Q8 23  
2OE 24  
30 2D5  
29 2D6  
28 GND  
27 2D7  
26 2D8  
25 2CLK  
description  
The  
’AHCT16374  
devices  
are  
16-bit  
edge-triggered D-type flip-flops with 3-state  
outputs designed specifically for driving highly  
capacitive or relatively low-impedance loads.  
They are particularly suitable for implementing  
buffer registers, I/O ports, bidirectional bus  
drivers, and working registers.  
These devices can be used as two 8-bit flip-flops or one 16-bit flip-flop. On the positive transition of the clock  
(CLK) input, the Q outputs of the flip-flop take on the logic levels at the data (D) inputs.  
A buffered output-enable (OE) input can be used to place the eight outputs in either a normal logic state (high  
or low logic levels) or the high-impedance state. In the high-impedance state, the outputs neither load nor drive  
the bus lines significantly. The high-impedance state and the increased drive provide the capability to drive bus  
lines without need for interface or pullup components.  
To ensure the high-impedance state during power up or power down, OE should be tied to V through a pullup  
CC  
resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.  
OE does not affect internal operations of the flip-flop. Old data can be retained or new data can be entered while  
the outputs are in the high-impedance state.  
The SN54AHCT16374 is characterized for operation over the full military temperature range of –55°C to 125°C.  
The SN74AHCT16374 is characterized for operation from –40°C to 85°C.  
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of  
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.  
EPIC and Widebus are trademarks of Texas Instruments Incorporated.  
Copyright 2000, Texas Instruments Incorporated  
UNLESS OTHERWISE NOTED this document contains PRODUCTION  
DATA information current as of publication date. Products conform to  
specifications per the terms of Texas Instruments standard warranty.  
Production processing does not necessarily include testing of all  
parameters.  
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265  
1234567...13

中文翻译

下载PDF

SN74AHCT16374DLR 替代型号

型号 品牌 替代类型 描述 数据表
SN74AHCT16374DL TI

完全替代

 16-BIT EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS
SN74AHCT16374DLG4 TI

类似代替

 16-BIT EDGE-TRIGGERED D-TYPE FLIP-FLOPS WITH 3-STATE OUTPUTS

与SN74AHCT16374DLR相关器件

型号 品牌 获取价格 描述 数据表
SN74AHCT164 TI

获取价格

 		4.5V 至 5.5V 8 位并行输出串行移位寄存器
SN74AHCT164PWR TI

获取价格

4.5V 至 5.5V 8 位并行输出串行移位寄存器

| PW | 14 |
SN74AHCT164-Q1 TI

获取价格

 		汽车级 4.5V 至 5.5V 8 位并行输出串行移位寄存器
SN74AHCT164QPWRQ1 TI

获取价格

汽车级 4.5V 至 5.5V 8 位并行输出串行移位寄存器

| PW |
SN74AHCT165 TI

获取价格

 		2-V to 5.5-V, 8-bit parallel-load shift registers with TTL inputs
SN74AHCT16540 TI

获取价格

 		16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS
SN74AHCT16540DGG TI

获取价格

 		16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS
SN74AHCT16540DGGR TI

获取价格

 		16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS
SN74AHCT16540DGV TI

获取价格

 		16-BIT BUFFERS/DRIVERS WITH 3-STATE OUTPUTS
SN74AHCT16540DGVR TI

获取价格

 		16-Bit Buffers/Drivers With 3-State Outputs 48-TVSOP -40 to 85

与SN74AHCT16374DLR相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证