ꢀ
ꢁ
ꢂ
ꢃ
ꢄ
ꢅ
ꢆ
ꢇ
ꢈ
ꢃ
ꢉ
DGK
D
P
www.ti.com
SLLS612 − JUNE 2004
ꢄ
ꢊ
ꢋ
ꢌ
ꢍ
ꢆ
ꢎ
ꢏ
ꢋ
ꢉ
ꢐ
ꢑ
ꢀ
ꢍ
ꢇ
ꢈ
ꢃ
ꢒ
ꢑ
ꢊ
ꢁ
ꢀ
ꢓ
ꢉ
ꢔ
ꢅ
ꢉ
ꢑ
FEATURES
DESCRIPTION
The SN65HVD485E is a half-duplex transceiver designed
for RS-485 data bus networks. Powered by a 5-V supply,
it is fully compliant with the TIA/EIA-485A standard. This
device is suitable for data transmission up to 10 Mbps over
long twisted-pair cables and is designed to operate with
very low supply current, typically less than 2 mA, exclusive
of the load. When in the inactive shutdown mode, the
supply current drops below 1 mA.
D
D
D
D
D
Bus-Pin ESD Protection Up to 15 kV
1/2 Unit Load—Up to 64 Nodes on a Bus
Bus Open Failsafe Receiver
Available in Small MSOP-8 Package
Meets or Exceeds the Requirements of the
TIA/EIA−485A Standard
D
Industry-Standard SN75176 Footprint
The wide common-mode range and high ESD protection
levels of this device make it suitable for demanding
applications such as, electrical inverters, status/command
signals across telecom racks, cabled chassis
interconnects, and industrial automation networks where
noise tolerance is essential. The SN65HVD485E matches
the industry-standard footprint of the SN75176. Power-on
reset circuits keep the outputs in a high-impedence state
until the supply voltage has stabilized. A thermal shutdown
function protects the device from damage due to system
fault conditions. The SN65HVD485E is characterized for
operation from −40°C to 85°C air temperature.
APPLICATIONS
D
D
D
D
D
D
D
Motor Control
Power Inverters
Industrial Automation
Building Automation Networks
Industrial Process Control
Battery-Powered Applications
Telecommunications Equipment
Improved Replacement for:
PART NUMBER REPLACE WITH
ADM485
HVD485E: Better ESD protection ( 15 kV vs. unspecified)
Faster signaling rate (10 Mbps vs. 5 Mbps)
More nodes on a bus (64 vs. 32)
Wider power supply tolerance (10% vs. 5%)
SP485E
HVD485E: More nodes on a bus (64 vs. 32)
Wider power supply tolerance (10% vs. 5%)
LMS485E
HVD485E: Higher signaling rate (10 Mbps vs. 2.5 Mbps)
More nodes on a bus (64 vs. 32)
Wider power supply tolerance (10% vs. 5%)
DS485
HVD485E: Higher signaling rate (10 Mbps vs. 2.5 Mbps)
Better ESD ( 15 kV vs. 2 kV)
More nodes on a bus (64 vs. 32)
Wider power supply tolerance (10% vs. 5%)
LTC485
HVD485E: Better ESD ( 15 kV vs. 2 kV)
Wider power supply tolerance (10% vs. 5%)
MAX485E
HVD485E: Higher signaling rate (10 Mbps vs. 2.5 Mbps)
More nodes on a bus (64 vs. 32)
Wider power supply tolerance (10% vs. 5%)
ST485E
HVD485E: Higher signaling rate (10 Mbps vs. 5 Mbps)
Wider power supply tolerance (10% vs. 5%)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
ꢏꢑ ꢕ ꢆꢎ ꢓ ꢒꢔ ꢕꢁ ꢆ ꢊꢒꢊ ꢖꢗ ꢘꢙ ꢚ ꢛꢜ ꢝꢖꢙꢗ ꢖꢞ ꢟꢠ ꢚ ꢚ ꢡꢗꢝ ꢜꢞ ꢙꢘ ꢢꢠꢣ ꢤꢖꢟ ꢜꢝꢖ ꢙꢗ ꢥꢜ ꢝꢡꢦ ꢏꢚ ꢙꢥꢠ ꢟꢝꢞ
ꢟ ꢙꢗ ꢘꢙꢚ ꢛ ꢝꢙ ꢞ ꢢꢡ ꢟ ꢖ ꢘꢖ ꢟ ꢜ ꢝꢖ ꢙꢗꢞ ꢢ ꢡꢚ ꢝꢧꢡ ꢝꢡ ꢚ ꢛꢞ ꢙꢘ ꢒꢡꢨ ꢜꢞ ꢔꢗꢞ ꢝꢚ ꢠꢛ ꢡꢗꢝ ꢞ ꢞꢝ ꢜꢗꢥ ꢜꢚ ꢥ ꢩ ꢜꢚ ꢚ ꢜ ꢗꢝꢪꢦ
ꢏꢚ ꢙ ꢥꢠꢟ ꢝ ꢖꢙ ꢗ ꢢꢚ ꢙ ꢟ ꢡ ꢞ ꢞ ꢖꢗ ꢫ ꢥꢙ ꢡ ꢞ ꢗꢙꢝ ꢗꢡ ꢟꢡ ꢞꢞ ꢜꢚ ꢖꢤ ꢪ ꢖꢗꢟ ꢤꢠꢥ ꢡ ꢝꢡ ꢞꢝꢖ ꢗꢫ ꢙꢘ ꢜꢤ ꢤ ꢢꢜ ꢚ ꢜꢛ ꢡꢝꢡ ꢚ ꢞꢦ
Copyright 2004, Texas Instruments Incorporated