ꢀꢁꢂ ꢃ ꢄꢅ ꢆ ꢆ ꢇ ꢈ ꢀꢁ ꢉꢃ ꢄꢅ ꢆꢆ ꢇ
ꢒ
ꢛ
ꢅ
ꢊ
ꢋ
ꢌ ꢍ
ꢃ
ꢎ
ꢃ
ꢊ
ꢋ
ꢀ
ꢏ
ꢁ
ꢐ
ꢑ
ꢒ
ꢊ
ꢄ
ꢓ
ꢔ
ꢁ
ꢁ
ꢒ
ꢑ
ꢕ
ꢀ
ꢊ
ꢆ
ꢅ
ꢆ
ꢄ
ꢍ
ꢖ
ꢗ
ꢔ
ꢌ
ꢏ
ꢘ
ꢑ
ꢒ
ꢑ
ꢏ
ꢁ
ꢙ
ꢕ
ꢏ
ꢋ
ꢒ
ꢕ
ꢚ
ꢕ
ꢒ
ꢄ
ꢒ
ꢏ
ꢋ
ꢒ
ꢕ
ꢛ
SLLS351E − APRIL 2002 − REVISED OCTOBER 2004
DB OR PW PACKAGE
(TOP VIEW)
D
Operate With 3-V to 5.5-V V
Operate Up To 1 Mbit/s
Supply
CC
D
D
D
D
D
Low Standby Current . . . 1 µA Typ
External Capacitors . . . 4 × 0.1 µF
EN
C1+
V+
FORCEOFF
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
V
CC
GND
Accepts 5-V Logic Input With 3.3-V Supply
C1−
C2+
C2−
V−
DOUT
FORCEON
DIN
RS-232 Bus-Pin ESD Protection Exceeds
15 kV Using Human-Body Model (HBM)
D
D
Auto-Powerdown Feature Automatically
Disables Drivers for Power Savings
INVALID
ROUT
RIN
Applications
− Battery-Powered, Hand-Held, and
Portable Equipment
− PDAs and Palmtop PCs
− Notebooks, Sub-Notebooks, and Laptops
− Digital Cameras
− Mobile Phones and Wireless Devices
description/ordering information
The SN65C3221 and SN75C3221 consist of one line driver, one line receiver, and a dual charge-pump circuit
with 15-kV ESD protection pin to pin (serial-port connection pins, including GND). These devices provide the
electrical interface between an asynchronous communication controller and the serial-port connector. The
charge pump and four small external capacitors allow operation from a single 3-V to 5.5-V supply. These devices
operate at data signaling rates up to 1 Mbit/s and a driver output slew rate of 24 V/µs to 150 V/µs.
Flexible control options for power management are available when the serial port is inactive. The
auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of
operation, if the devices do not sense a valid RS-232 signal on the receiver input, the driver output is disabled.
If FORCEOFF is set low and EN is high, both the driver and receiver are shut off, and the supply current is
reduced to 1 µA. Disconnecting the serial port or turning off the peripheral drivers causes the auto-powerdown
condition to occur. Auto-powerdown can be disabled when FORCEON and FORCEOFF are high. With
auto-powerdown enabled, the device is activated automatically when a valid signal is applied to the receiver
input. The INVALID output notifies the user if an RS-232 signal is present at the receiver input. INVALID is high
(valid data) if the receiver input voltage is greater than 2.7 V or less than −2.7 V, or has been between −0.3 V
and 0.3 V for less than 30 µs. INVALID is low (invalid data) if the receiver input voltage is between −0.3 V and
0.3 V for more than 30 µs. Refer to Figure 5 for receiver input levels.
ORDERING INFORMATION
ORDERABLE
PART NUMBER
TOP-SIDE
MARKING
†
T
A
PACKAGE
SSOP (DB)
Reel of 2000
Tube of 90
SN75C3221DBR
SN75C3221PW
SN75C3221PWR
SN65C3221DBR
SN65C3221PW
SN65C3221PWR
CA3221
−0°C to 70°C
−40°C to 85°C
TSSOP (PW)
SSOP (DB)
CA3221
CB3221
Reel of 2000
Reel of 2000
Tube of 90
TSSOP (PW)
CB3221
Reel of 2000
†
Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are
available at www.ti.com/sc/package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
ꢗ
ꢗ
ꢕ
ꢍ
ꢬ
ꢙ
ꢧ
ꢜ
ꢄ
ꢥ
ꢌ
ꢦ
ꢏ
ꢠ
ꢍ
ꢞ
ꢁ
ꢟ
ꢙ
ꢔ
ꢌ
ꢔ
ꢝ
ꢞ
ꢨ
ꢟ
ꢠ
ꢦ
ꢡ
ꢢ
ꢣ
ꢣ
ꢤ
ꢤ
ꢝ
ꢝ
ꢠ
ꢠ
ꢞ
ꢞ
ꢝ
ꢥ
ꢥ
ꢩ
ꢦ
ꢧ
ꢡ
ꢡ
ꢨ
ꢨ
ꢞ
ꢤ
ꢣ
ꢢ
ꢥ
ꢥ
ꢠ
ꢟ
ꢩ
ꢌꢨ
ꢧ
ꢪ
ꢥ
ꢫ
ꢝ
ꢦ
ꢣ
ꢥ
ꢤ
ꢝ
ꢤ
ꢠ
ꢡ
ꢞ
ꢧ
ꢬ
ꢣ
ꢞ
ꢤ
ꢤ
ꢨ
ꢥ
ꢎ
Copyright 2004, Texas Instruments Incorporated
ꢡ
ꢠ
ꢦ
ꢤ
ꢠ
ꢡ
ꢢ
ꢤ
ꢠ
ꢥ
ꢩ
ꢝ
ꢟ
ꢝ
ꢦ
ꢨ
ꢡ
ꢤ
ꢭ
ꢤ
ꢨ
ꢡ
ꢠ
ꢟ
ꢮ
ꢣ
ꢏ
ꢞ
ꢢ
ꢨ
ꢥ
ꢤ
ꢣ
ꢞ
ꢬ
ꢣ
ꢡ
ꢬ
ꢯ
ꢣ
ꢤ ꢨ ꢥ ꢤꢝ ꢞꢱ ꢠꢟ ꢣ ꢫꢫ ꢩꢣ ꢡ ꢣ ꢢ ꢨ ꢤ ꢨ ꢡ ꢥ ꢎ
ꢡ
ꢡ
ꢣ
ꢞ
ꢤ
ꢰ
ꢎ
ꢗ
ꢡ
ꢠ
ꢬ
ꢧ
ꢦ
ꢤ
ꢝ
ꢠ
ꢞ
ꢩ
ꢡ
ꢠ
ꢦ
ꢨ
ꢥ
ꢥ
ꢝ
ꢞ
ꢱ
ꢬ
ꢠ
ꢨ
ꢥ
ꢞ
ꢠ
ꢤ
ꢞ
ꢨ
ꢦ
ꢨ
ꢥ
ꢥ
ꢣ
ꢡ
ꢝ
ꢫ
ꢰ
ꢝ
ꢞ
ꢦ
ꢫ
ꢧ
ꢬ
ꢨ
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265