5秒后页面跳转
捷配首页

Datasheet > SI-5154S
SI-5154S PDF预览

SI-5154S

更新时间： 2024-11-24 22:43:15
品牌 Logo 应用领域
三垦 - SANKEN 二极管齐纳二极管开关电源开关
页数 文件大小 规格书
2页 31K
描述
High-side Power Switch with Diagnostic Function and Built-in Zener Diode

阅读下载

中文翻译

获取价格

SI-5154S 技术参数

生命周期：Obsolete零件包装代码：SFM
包装说明：,针数：3
Reach Compliance Code：unknownECCN代码：EAR99
HTS代码：8542.39.00.01风险等级：5.84
内置保护：TRANSIENT; OVER CURRENT; THERMAL接口集成电路类型：BUFFER OR INVERTER BASED PERIPHERAL DRIVER
JESD-30 代码：R-PZFM-T5功能数量：1
端子数量：5最高工作温度：100 °C
最低工作温度：-40 °C输出电流流向：SOURCE
标称输出峰值电流：2.5 A封装主体材料：PLASTIC/EPOXY
封装形状：RECTANGULAR封装形式：FLANGE MOUNT
认证状态：Not Qualified最大供电电压：30 V
最小供电电压：6 V标称供电电压：14 V
表面贴装：NO温度等级：INDUSTRIAL
端子形式：THROUGH-HOLE端子位置：ZIG-ZAG
断开时间：30 µs接通时间：30 µs
Base Number Matches：1

SI-5154S 数据手册

 浏览型号SI-5154S的Datasheet PDF文件第2页 
High-side Power Switch with Diagnostic Function and Built-in Zener Diode SI-5154S  
(unit: mm)  
External Dimensions  
Features  
● Built-in diagnostic function to detect short and open circuiting of loads and  
output status signals  
3.2 ±0.2  
4.2 ±0.2  
2.8 ±0.2  
10 ±0.2  
● Low saturation PNP transistor use  
● Allows direct driving using LS-TTL and C-MOS logic levels  
● Built-in overcurrent and thermal protection circuits  
● Built-in protection against reverse connection of power supply  
● Tj = 150ºC guaranteed  
a
2.6 ±0.1  
b
● Built-in Zener diode  
● TO-220 equivalent full-mold package not require insulation mica  
0.94 ±0.15  
+0.2  
–0.1  
0.45  
+0.2  
–0.1  
Absolute Maximum Ratings  
0.85  
(Ta =25ºC)  
P1.7 ±0.15 • 4  
4 ±0.6  
Parameter  
Power supply voltage  
Input terminal voltage  
DIAG terminal voltage  
Symbol  
Ratings  
–13 to +40  
–0.3 to VB  
6
Unit  
V
Conditions  
VB  
1. GND  
a: Type No.  
b: Lot No.  
V
IN  
V
2. V  
IN  
3. V  
o
VDIAG  
VCE  
V
1
2
3
4
5
4. DIAG  
5. VB  
Refer to "Surge clamp voltage" in  
Electrical Characteristics  
Collector-emitter voltage  
Output current  
VB –VZ  
V
(Forming No. 1111)  
IO  
PD1  
PD2  
Tj  
2.5  
22  
A
W
W
ºC  
ºC  
ºC  
With infinite heatsink (Tc =25ºC)  
Stand-alone without heatsink  
Power Dissipation  
1.8  
Junction temperature  
Operating temperature  
Storage temperature  
–40 to +150  
–40 to +100  
–40 to +150  
Standard Circuit Diagram  
TOP  
Tstg  
VB  
5
VO  
3
Electrical Characteristics  
SI-5154S  
(Ta =25ºC unless otherwise specified)  
VCC  
V
IN  
Ratings  
typ  
2
DIAG  
Parameter  
Symbol  
Unit  
Conditions  
min  
6.0  
max  
30  
4
5.1kΩ  
LS-TTL  
or  
VBopr  
Iq  
V
mA  
V
Operating power supply voltage  
Quiescent circuit current  
1
CMOS  
5
12  
VBopr =14V, VIN = 0 V  
0.3  
0.72  
2
IO 1.0A, VBopr =6 to 16V  
IO 2.5A, VBopr =6 to 16V  
Saturation voltage of output  
transistor  
VCE (sat)  
IO, leak  
V
GND  
Truth table  
V
IN  
VO  
H
mA  
V
V
CEO =16V, VIN = 0 V  
Bopr =6 to 16V  
VBopr =6 to 16V  
Output leak current  
H
V
2.0  
VB  
V
Output ON  
Input voltage  
IH  
L
L
V
IL  
–0.3  
0.8  
1
V
Output OFF  
IIH  
IIL  
mA  
mA  
V
IN = 5 V  
Output ON  
Input current  
–0.1  
2.6  
VIN = 0 V  
Output OFF  
Overcurrent protection starting  
current  
IS  
A
VBopr = 14V, VO = VBopr –1.5V  
Diagnostic Function  
Thermal protection starting  
temperature  
TTSD  
150  
ºC  
VBopr 6V  
Normal  
Open load  
Shorted load  
Overheat  
Normal  
Ropen  
TON  
TOFF  
VDH  
VDL  
30  
30  
30  
6
kΩ  
µS  
µS  
V
VBopr =6 to 16V  
Bopr =14V, IO = 1 A  
Bopr =14V, IO = 1 A  
CC =6V, VBopr =6 to 16V  
Open load detection resistor  
V
IN  
8
V
Output transfer time  
VO  
15  
V
4.5  
V
DIAG output voltage  
DIAG  
0.3  
30  
30  
V
V
CC  
=6V,  
V
Bopr  
=6 to 16V,  
I
DO  
=2mA  
TPLH  
TPHL  
L
µS  
µS  
mH  
V
VBopr =14V, IO = 1 A  
Bopr =14V, IO = 1 A  
DIAG output transfer time  
V
V
IN  
VO  
DIAG  
Mode  
L
H
L
H
L
H
L
H
L
H
H
H
L
L
L
L
L
H
H
H
L
L
L
L
Minimum load inductance  
1
Normal  
1
Surge clamp voltage  
*
VZ  
28  
34  
40  
IC =5mA  
Open load  
S h o rte d lo a d  
Overheat  
Note:  
*1. The Zener diode for surge clamping has an energy capability of 200 mJ (single pulse).  
* The rule of protection against reverse connection of power supply is VB = –13V, one minute.  
* This driver is exclusively used for ON/OFF control.  
● DIAG output will be undetermined when a voltage  
exceeding 25V is applied to VB terminal.  
26  
12

中文翻译

下载PDF

与SI-5154S相关器件

型号 品牌 获取价格 描述 数据表
SI-5155S SANKEN

获取价格

 		High-side Power Switch with Diagnostic Function
SI-5174-F BEL

获取价格

 		Telecom and Datacom Connector, ROHS COMPLIANT
SI-52001 BEL

获取价格

 		Telecom and Datacom Connector
SI-52001-F BEL

获取价格

 		SI-52001-F
SI-52002 BEL

获取价格

 		SI-52002
SI-52002-F BEL

获取价格

 		SI-52002-F
SI-52003-F BEL

获取价格

 		SI-52003-F
SI-52004-F BEL

获取价格

 		SI-52004-F
SI-52005-F BEL

获取价格

 		SI-52005-F
SI-52006-F BEL

获取价格

 		SI-52006-F

与SI-5154S相关文章

您还可以找


热门产品
PCB打样/小批量
铝基板
BOM智能配单
PCBA制造
钣金
精密CNC
模具注塑
薄膜开关
精选活动
PCBA打样特惠
四六层板品质升级
铝基板品质升级
一体化电子制造
DFM下载
服务支持
企业认证
产品展示
工厂展示
工艺能力
积分商城
关于捷配
捷配简介
企业文化
公司动态
人才招聘
联系我们
帮助中心
下单流程
付款流程
开票流程
常见问题
全球PCB制造服务专线 400-613-0088

工作时间：9:00-21:00

CEO邮箱：ceo@jiepei.com

投诉邮箱：tousu@jiepei.com

捷配网-微信公众号 微信公众号
捷配网-微信公众号 抖音公众号
资质认证：
合作快递：
支付方式：
Copyright © 2024 Jiepei.com Inc. All Rights Reserved. 版权所有:杭州捷配信息科技有限公司 浙公网安备 33010502006866号 浙ICP备10014259号-119 营业执照ICP证