SF2182D
• 22 MHz Filter Bandwidth
• 3.8 x 3.8 x 1.4 mm Surface-mount Package
• Complies with Directive 2002/95/EC (RoHS)
140 MHz
Pb
SAW Filter
Absolute Maximum Ratings
Rating
Value
+10
Units
dBm
VDC
°C
Maximum Incident Power in Passband
Maximum DC Voltage on any Non-ground Terminal
Storage Temperature Range in Tape and Reel
Suitable for Lead-free Soldering - Maximum Soldering Profile
3
-40 to +85
260°C for 30 s
SM3838-8
Electrical Characteristics
Characteristic
Sym
Notes
Min
Typ
140
Max
Units
MHz
dB
Nominal Center Frequency
Insertion Loss
F
1
1
1
1
1
1
C
IL
13.5
15.0
1
MAX
Insertion Loss Variation over Temperature
3 dB Bandwidth
dB
40
43
0.8
1.2
MHz
Passband Amplitude Ripple, Single-ended Matching, 120 to 160 MHz
Passband Amplitude Ripple, Balanced Matching, 120 to 160 MHz
1.5
2.0
dB
dB
P-P
P-P
Absolute Attenuation (referenced to IL
10 to 70 MHz
)
MAX
3
3
3
3
1
1
1
1
1
1
1
1
45
25
25
45
50
40
70 to 115 MHz
dB
166.5 to 200 MHz
40
200 to 400 MHz
50
Absolute Group Delay in Passband
400
20
450
50
ns
ns
Passband Group Delay Ripple, Matching Network A or B, 129 to 151 MHz
Input Impedance, Unbalanced Matching Network
Input Impedance, Balanced Matching Network
Input Return Loss through any Matching Network
Output Impedance, Unbalanced Matching Network
Output Impedance, Balanced Matching Network
Output Return Loss through any Matching Network
Operating Temperature Range
P-P
50
ohm
ohm
dB
200
8
3
50
ohm
ohm
dB
200
10
3
-40
+85
°C
Case Style
SM3838-8 3.8 x 3.8 mm Nominal Footprint
RFM 873 YWWS
Lid Symbolization (Y=year, WW=week, S=shift)
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
1.
Unless noted otherwise, all specifications apply over the operating temper-
ature range with filter soldered to the specified demonstration board with
impedance matching to 50 Ω and measured with 50 Ω network analyzer.
Unless noted otherwise, all frequency specifications are referenced to the
nominal center frequency, fc.
Rejection in final user application is dependent on PCB layout and
external impedance matching design. See Application Note No. 42 for
details.
"LRIP" or "L" after the part number indicates "low rate initial production"
and "ENG" or "E" indicates "engineering prototypes."
5.
6.
The design, manufacturing process, and specifications of this filter are
subject to change.
Either Port 1 or Port 2 may be used for either input or output in the design.
However, impedances and impedance matching may vary between Port 1
and Port 2, so that the filter must always be installed in one direction per
the circuit design.
US and international patents may apply.
RFM, stylized RFM logo, and RF Monolithics, Inc. are registered
trademarks of RF Monolithics, Inc.
2.
3.
7.
8.
4.
www.RFM.com E-mail: info@rfm.com
©2010 by RF Monolithics, Inc.
Page 1 of 14
SF2182D - 5/28/10