®
SF2079D
•
•
•
•
Low Insertion Loss
3.8 X 3.8 mm Surface-Mount Case
Single Ended Input and Output
Complies with Directive 2002/95/EC (RoHS)
251.045 MHz
Pb
SAW Filter
Absolute Maximum Ratings
Rating
Value
+13
Units
dBm
VDC
°C
Maximum Incident Power in Passband
Max. DC voltage between any 2 terminals
Storage Temperature Range
30
-40 to +85
Suitable for lead-free soldering - Max Soldering Temperature
260°C for 30 s
SM3838-8
Electrical Characteristics
Characteristic
Sym
Notes
Min
Typ
Max
Units
Nominal Center Frequency
f
1
251.045
MHz
C
Insertion Loss
1
15.5
0.7
0.5
0.8
0.9
0.5
0.6
13.9
14.5
37
17.5
1.5
1.5
1.5
1.5
1.5
1.5
dB
dB
Amplitude Ripple (p-p)
Fc-6.250 to Fc-4.3925 MHz
Fc-4.3925 to Fc-2.535 MHz
Fc-2.5350 to Fc-0.025 MHz
Fc+0.025 to Fc+2.535 MHz
Fc+2.5350 to Fc+4.3925 MHz
Fc+4.3925 to Fc+6.250 MHz
dB
dB
dB
dB
dB
Pass bandwidth of -1.5dB
MHz
MHz
dB
Pass bandwidth of -3dB
Low side attenuation Fc<(Fc-16.5 MHz)
33
28
24
35
Low side attenuation between: (Fc-16.5 MHz)...(Fc-10.5 MHz)
High side attenuation between: (Fc+9.0 MHz)...(Fc+16.5 MHz)
High side attenuation Fc>(Fc+16.5 MHz)
32
dB
30
dB
40
dB
Temperature Coefficient of frequency
-18
70
70
90
90
70
90
ppm/K
ns
Delay Ripple (p-p)
Fc-6.250 to Fc-4.3925 MHz
45
25
Fc-4.3925 to Fc-2.535 MHz
Fc-2.5350 to Fc-0.025 MHz
Fc+0.025 to Fc+2.535 MHz
Fc+2.5350 to Fc+4.3925 MHz
Fc+4.3925 to Fc+6.250 MHz
ns
20
ns
15
ns
25
ns
45
ns
Terminating Source / Load Impedance: Z / Z
150
Ohms
°C
IN
OUT
Operating Temperature Range
Case Style
-40
+85
SM3838-8 3.8 x 3.8 mm Nominal Footprint
RFM TBD YWWS
Lid Symbolization (Y=year, WW=week, S=shift)
Notes:
1.
Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to
50 W and measured with 50 W network analyzer.
2.
Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance
matching design. See Application Note No. 42 for details.
3.
4.
5.
The design, manufacturing process, and specifications of this filter are subject to change.
Tape and Reel Standard ANSI / EIA 481.
Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that
the filter must always be installed in one direction per the circuit design.
6.
7.
8.
9.
US and international patents may apply.
RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
©Copyright 1999, RF Monolithics Inc.
Electrostatic Sensitive Device. Observe precautions for handling.
RF Monolithics, Inc.
RFM Europe
Phone: (972) 233-2903
Phone: 44 1963 251383
Fax: (972) 387-8148
Fax: 44 1963 251510
E-mail: info@rfm.com
http://www.rfm.com
SF2079D-060607
Page 1 of 5
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.