Preliminary
SF2079D-1
• Low Insertion Loss
• 3.8 X 3.8 X 1 mm Surface-Mount Case
• Differential Input and Output
• Complies with Directive 2002/95/EC (RoHS)
251.045 MHz
SAW Filter
Pb
Absolute Maximum Ratings
Rating
Value
Units
Maximum Incident Power in Passband
+10
dBm
Maximum DC Voltage Between any Two Terminals
Operating Temperature Range
30
VDC
°C
-40 to +85
-60 to +95
Storage Temperature Range
°C
Suitable for Lead-free Soldering - Maximum Soldering Profile
260°C for 30 s
SM3838-8
Electrical Characteristics
Characteristic
Center Frequency
Insertion Loss
Sym
Notes
Min
Typ
251.045
13.0
Max
Units
MHz
dB
f
C
1
IL
15.0
1.75
1.50
1.50
1.50
1.75
1.75
Amplitude Ripple (p-p)
fc - 6.2500 to fc - 4.3925 MHz
0.90
fc - 4.3925 to fc - 2.5350 MHz
fc - 2.5350 to fc - 0.0250 MHz
fc + 0.0250 to fc + 2.5350 MHz
fc + 2.5350 to fc + 4.3925 MHz
fc + 4.3925 to fc + 6.2500 MHz
0.60
0.60
dB
0.80
1, 2
0.80
0.60
1.5 dB Passband Width Centered at fc
3.0 dB Passband Width Centered at fc
13.5
MHz
14.2
Low Side Attenuation < 234.545 MHz ( < fc - 16.5 MHz)
Low Side Attenuation, 234.545 to 240.545 MHz (fc-10.5 MHz)
High Side Attenuation, 260.045 to 267.545 MHz (fc+9.0 MHz)
High Side Attenuation > 267.545 MHz ( > fc + 16.5 MHz)
Temperature Coefficient of frequency
32
29
18
32
dB
-18
150
70
ppm/K
Delay Ripple (p-p)
fc - 6.2500 to fc - 4.3925 MHz
1, 2, 3
84
35
fc - 4.3925 to fc - 2.5350 MHz
fc - 2.5350 to fc - 0.0250 MHz
fc + 0.0250 to fc + 2.5350 MHz
fc + 2.5350 to fc + 4.3925 MHz
fc + 4.3925 to fc + 6.2500 MHz
22
120
120
70
ns
58
37
52
110
Source/Load Impedance
Case Style
150
ohms
SM3838-8 3.8 x 3.8 mm Nominal Footprint
827 YWWS
6
Lid Symbolization (YY=year, WW=week, S=shift) See note 4
CAUTION: Electrostatic Sensitive Device. Observe precautions for handling.
Notes:
and external impedance matching design. See Application Note No. 42
for details.
Notes:
1.
Unless noted otherwise, all specifications apply over the operating
4.
The design, manufacturing process, and specifications of this filter are
subject to change.
temperature range with filter soldered to the specified demonstration
board with impedance matching to 50 Ω and measured with 50 Ω network
analyzer.
5.
6.
7.
Tape and Reel Standard Per ANSI / EIA 481.
US and international patents may apply.
RFM, stylized RFM logo, and RF Monolithics, Inc. are registered
trademarks of RF Monolithics, Inc.
2.
3.
Unless noted otherwise, all frequency specifications are referenced to the
nominal center frequency, fc.
Rejection is measured as attenuation below the minimum IL point in the
passband. Rejection in final user application is dependent on PCB layout
www.RFM.com E-mail: info@rfm.com
©2009 by RF Monolithics, Inc.
Page 1 of 5
SF2079D1 - 4/17/09