®
SF2040B-2
•
•
•
•
•
Designed for SDARS IF Receiver
Low Insertion Loss
5.0 X 7.0 mm Surface-Mount Case
Differential or Single Ended Input and Output
Complies with Directive 2002/95/EC (RoHS)
80.460 MHz
SAW Filter
Pb
Absolute Maximum Ratings
Rating
Value
+10
Units
dBm
VDC
°C
Maximum Incident Power in Passband
Max. DC voltage between any 2 terminals
Storage Temperature Range (with tape & reel)
Storage Temperature Range (without tape & reel)
Max Soldering Profile
30
-40 to +85
-50 to +125
°C
265°C for 10 s
SMP-03
Electrical Characteristics
Characteristic
Sym
Notes
Min
Typ
Max
Units
Nominal Center Frequency
f
80.460
9.5
4.1
6.6
7.6
0.5
60
MHz
C
1
Passband
Insertion Loss
IL
12.0
dB
1dB Passband
15dB Bandwidth
30dB Bandwidth
BW
3.7
MHz
MHz
MHz
1
BW
BW
6.7
7.7
15
30
1
Amplitude Ripple over fc ±1.85 MHz
Group Delay Variation over fc ±1.85 MHz
50 to 74.39 MHz
1.10
150
dB
P-P
P-P
GDV
ns
Rejection
40
32
35
37
45
-40
44
74.39 to 75.99 MHz
40
1, 3
1
dB
85.21 to 86.5 MHz
44
86.5 to 91.50 MHz
48
91.50 to 100 MHz
53
Operating Temperature Range
Frequency Temperature Coefficient
Differential Input
T
+105
°C
A
FTC
-18
ppm/°C
175 ohms
1000 ohms
Differential Output
Case Style
SMP-03 7 x 5 mm Nominal Footprint
RFM SF2040B-2 YYWWS
6
Lid Symbolization (YY=year, WW=week, S=shift) See note 4
Electrical Connections
Connection
Terminals
Port 1 Hot
10
Port 1 Ground Return
Port 2 Hot
1
5
6
Port 2 Ground Return
Case Ground
All Others
Notes:
1.
Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to
50 W and measured with 50 W network analyzer.
2.
3.
Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc.
Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance
matching design. See Application Note No. 42 for details.
4.
5.
6.
7.
"LRIP" or "L" after the part number indicates "low rate initial production" and "ENG" or "E" indicates "engineering prototypes."
The design, manufacturing process, and specifications of this filter are subject to change.
Tape and Reel Standard ANSI / EIA 481.
Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that
the filter must always be installed in one direction per the circuit design.
8.
9.
US and international patents may apply.
RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of RF Monolithics, Inc.
10. ©Copyright 1999, RF Monolithics Inc.
11. Electrostatic Sensitive Device. Observe precautions for handling.
RF Monolithics, Inc.
RFM Europe
Phone: (972) 233-2903
Phone: 44 1963 251383
Fax: (972) 387-8148
Fax: 44 1963 251510
E-mail: info@rfm.com
http://www.rfm.com
SF2040B-2-022607
Page 1
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.