®
SF1189B-1
•
•
•
•
•
•
Designed for WLAN IF Applications
Low Insertion Loss
5.0 x 5.0 x 1.7 mm Suface-Mount Case
Single Ended or Differential Input and Output
Differential Output
280.00 MHz
SAW Filter
Pb
Complies with Directive 2002/95/EC (RoHS)
Absolute Maximum Ratings
Rating
Value
+10
Units
dBm
VDC
°C
Maximum Incident Power in Passband
Max. DC voltage between any 2 terminals
Storage Temperature Range
0
-40 to +85
SM5050-8
Suitable for lead-free soldering - Max Soldering Profile
260°C for 30 s
Electrical Characteristics
Characteristic
Sym
Notes
Min
Typ
Max
Units
f
1
280.0
8.3
19.3
2.0
60
Nominal Center Frequency
MHz
dB
C
Passband
Insertion Loss at fc
3 dB Passband
10
IL
BW
1, 2
17.97
MHz
3
dB
Amplitude Ripple over fc ±9.0 MHz
Group Delay Variation over fc ±9.0
fc -60 to fc -40 MHz
3.0
P-P
ns
GDV
125
P-P
1, 2, 3
Rejection
40
37
30
25
34
40
-10
46
fc -40 to fc -22 MHz
39
fc -22 to fc -16 MHz
39
dB
°C
fc +16 to fc +22 MHz
33
fc +22 to fc +40 MHz
36
fc +40 to fc +60 MHz
45
T
Operating Temperature Range
+85
1
A
Differential Input / Output Impedance Match
Case Style
External L-C
SM5050-8 5 X 5 mm Nominal Footprint
457, YYWWS
Lid Symbolization (YY=year, WW=week, S=shift)
Electrical Connections
22 pf
50
27 nH
4:1
pin 3
pin 7
Connection
Single Ended Input
Terminals
SAW Filter
TOP VIEW
Port 1
Port 2
3
33 nH
15 pf
50
Differential Output
Ground
6,7
pin 6
All Others
All others
22 pf
RF IC
Notes:
figure 1
1.
Unless noted otherwise, all specifications apply over the operating temperature
range with filter soldered to the specified demonstration board with impedance
matching to 50 W and measured with 50 W network analyzer.
Unless noted otherwise, all frequency specifications are referenced to the nom-
inal center frequency, fc.
Rejection is measured as attenuation below the minimum IL point in the pass-
band. Rejection in final user application is dependent on PCB layout and exter-
nal impedance matching design. See Application Note No. 42 for details.
"LRIP" or "L" after the part number indicates "low rate initial production" and
"ENG" or "E" indicates "engineering prototypes."
5.
6.
The design, manufacturing process, and specifications of this filter are subject
to change.
Either Port 1 or Port 2 may be used for either input or output in the design.
However, impedances and impedance matching may vary between Port 1 and
Port 2, so that the filter must always be installed in one direction per the circuit
design.
US and international patents may apply.
RFM, stylized RFM logo, and RF Monolithics, Inc. are registered trademarks of
RF Monolithics, Inc.
2.
3.
7.
8.
4.
9.
©Copyright 1999, RF Monolithics Inc.
10. Electrostatic Sensitive Device. Observe precautions for handling.
RF Monolithics, Inc.
RFM Europe
Phone: (972) 233-2903
Phone: 44 1963 251383
Fax: (972) 387-8148
Fax: 44 1963 251510
E-mail: info@rfm.com
http://www.rfm.com
Page 1 of 5
©1999 by RF Monolithics, Inc. The stylized RFM logo are registered trademarks of RF Monolithics, Inc.
SF1189B-1-121604