15W Single Output DC-DC Converter
SD-15 series
Features :
2:1 wide input range
Protections:Short circuit/Over load /voltage
Built-in EMI filter,low ripple noise
100% full load burn-in test
Low cost
High reliability
1 year warranty
SPECIFICATION
MODEL
SD-15C-12
SD-15A-24
SD-15A-05
SD-15B-05
SD-15B-12
SD-15B-24
SD-15C-05
SD-15A-12
12V
SD-15C-24
24V
DC VOLTAGE
5V
0.625A
0 ~ 0.625A
15W
3A
1.25A
RATED CURRENT
CURRENT RANGE
RATED POWER
0 ~ 1.25A
15W
0 ~ 3A
15W
OUTPUT
150mVp-p
21.6~26.4VDC
1.0%
RIPPLE & NOISE (max.) Note.2 100mVp-p
120mVp-p
10.8~13.2VDC
1.0%
VOLTAGE ADJ.RANGE
VOLTAGE TOLERANCE Note.3
LINE REGULATION
4.75~5.5VDC
2.0%
0.5%
0.5%
0.2%
0.2%
0.3%
LOAD REGULATION
SETUP, RISE ,HOLD UP TIME
VOLTAGE RANGE
0.3%
2.5s, 25ms,--- 12VDC/24VDC/48VDC at full load
A: 9.2 ~18VDC
B:18 ~ 36VDC
75%
C:36~72VDC
72%
INPUT
79%
78%
EFFICIENCY(Typ.)
70%
77%
68%
76%
76%
DC CURRENT(Typ.)
1.9A/12VDC
0.9A/24VDC
0.45A/48VDC
105% -160% rated output power
OVER LOAD
Protection type : hiccup mode , recovers automatically after fault condition is removed
PROTECTION
13.8~ 16.2V
5.75 ~ 6.75V
27.6 ~ 32.4V
OVER VOLTAGE
Protection type : Shut down o/p voltage, re-power on to recover
¡
-10 60
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
20 ~ 90% RH non-condensing
ENVIRONMENT
0.03%/ (0 ~ 50
)
10 ~ 500Hz, 2G 10min./1cycle, 60min.each along X, Y, Z axes
I/P-O/P:2KVAC I/P-FG:1KVAC O/P-FG:0.5KVAC
I/P-O/P,I/P-FG,O/P-FG:100M Ohms/500VDC
Compliance to EN55022(CISPR22) CLASS B
Compliance to EN61000-4-2,3,4,6,8;ENV50204,EN55024,light industry level,criteria A
79*51*28mm (L*W*H)
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMI CONDUCTION&RADIATION
EMS IMMUNITY
SAFETY &
EMC
DIMENSION
OTHERS
NOTE
PACKING
0.18kg,60 PCS/11.8kg
1. All parameters NOT specially mentioned are measured at normal input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
File Name:SD-15 SPEC.2006-04-19