5秒后页面跳转
SA616 PDF预览

SA616

更新时间: 2024-01-07 22:40:44
品牌 Logo 应用领域
恩智浦 - NXP /
页数 文件大小 规格书
17页 164K
描述
Low-voltage high performance mixer FM IF system

SA616 技术参数

生命周期:Obsolete零件包装代码:SOIC
包装说明:LSSOP,针数:20
Reach Compliance Code:unknown风险等级:5.65
其他特性:IN-BUILT QUADRATURE DETECTOR商用集成电路类型:AUDIO SINGLE CHIP RECEIVER
解调类型:FMJESD-30 代码:R-PDSO-G20
长度:6.5 mm功能数量:1
端子数量:20最高工作温度:85 °C
最低工作温度:-40 °C标称输出电压(调频):130 mV
封装主体材料:PLASTIC/EPOXY封装代码:LSSOP
封装形状:RECTANGULAR封装形式:SMALL OUTLINE, LOW PROFILE, SHRINK PITCH
认证状态:Not Qualified座面最大高度:1.5 mm
信噪比Nom(FM):62 dB最大压摆率:5 mA
最大供电电压 (Vsup):7 V最小供电电压 (Vsup):2.7 V
表面贴装:YES温度等级:INDUSTRIAL
端子形式:GULL WING端子节距:0.65 mm
端子位置:DUAL宽度:4.4 mm
Base Number Matches:1

SA616 数据手册

 浏览型号SA616的Datasheet PDF文件第4页浏览型号SA616的Datasheet PDF文件第5页浏览型号SA616的Datasheet PDF文件第6页浏览型号SA616的Datasheet PDF文件第8页浏览型号SA616的Datasheet PDF文件第9页浏览型号SA616的Datasheet PDF文件第10页 
Philips Semiconductors  
Product specification  
Low-voltage high performance mixer FM IF system  
SA616  
RF GENERATOR  
NE616 DEMO BOARD  
45MHz  
RSSI AUDIO  
V
(+3)  
CC  
DE-EMPHASIS  
FILTER  
DC VOLTMETER  
C–MESSAGE  
HP339A DISTORTION  
ANALYZER  
SCOPE  
SR00371  
Figure 5. SA616 Application Circuit Test Set Up  
NOTES:  
1. C-message: The C-message and de-emphasis filter combination has a peak gain of 10 for accurate measurements. Without the gain, the  
measurements may be affected by the noise of the scope and HP339 analyzer. The de-emphasis filter has a fixed -6dB/Octave slope  
between 300Hz and 3kHz.  
2. Ceramic filters: The ceramic filters can be 30kHz SFG455A3s made by Murata which have 30kHz IF bandwidth (they come in blue), or  
16kHz CFU455Ds, also made by Murata (they come in black). All of our specifications and testing are done with the more wideband filter.  
3. RF generator: Set your RF generator at 45.000MHz, use a 1kHz modulation frequency and a 6kHz deviation if you use 16kHz filters, or  
8kHz if you use 30kHz filters.  
4. Sensitivity: The measured typical sensitivity for 12dB SINAD should be 0.35µV or -116dBm at the RF input.  
5. Layout: The layout is very critical in the performance of the receiver. We highly recommend our demo board layout.  
6. RSSI: The smallest RSSI voltage (i.e., when no RF input is present and the input is terminated) is a measure of the quality of the layout and  
design. If the lowest RSSI voltage is 500mV or higher, it means the receiver is in regenerative mode. In that case, the receiver sensitivity  
will be worse than expected.  
7. Supply bypass and shielding: All of the inductors, the quad tank, and their shield must be grounded. A 10-15µF or higher value tantalum  
capacitor on the supply line is essential. A low frequency ESR screening test on this capacitor will ensure consistent good sensitivity in  
production. A 0.1µF bypass capacitor on the supply pin, and grounded near the 44.545MHz oscillator improves sensitivity by 2-3dB.  
8. R5 can be used to bias the oscillator transistor at a higher current for operation above 45MHz. Recommended value is 22k, but should not  
be below 10k.  
7
1997 Nov 07  

与SA616相关器件

型号 品牌 描述 获取价格 数据表
SA616D NXP 暂无描述

获取价格

SA616DK NXP Low-voltage high performance mixer FM IF system

获取价格

SA616DK,112 NXP SA616 - Low-voltage high performance mixer FM IF system SSOP2 20-Pin

获取价格

SA616DK,118 NXP SA616 - Low-voltage high performance mixer FM IF system SSOP2 20-Pin

获取价格

SA616DK/01 NXP IC SPECIALTY TELECOM CIRCUIT, PDSO20, 4.40 MM, PLASTIC, MO-152, SOT-266-1, SSOP-20, Teleco

获取价格

SA616DK/01,118 NXP SA616 - Low-voltage high performance mixer FM IF system SSOP2 20-Pin

获取价格