RR7-S05/D05
5 Watt 4:1 regulated
single & dual output
■
■
■
■
■
■
■
■
DIP24, wide 4:1 input range
Full SMD technology
1500 VDC isolation up to 3500 VDC isolation
Continuous short circuit protection
Efficiency up to 82%
-40°C~85°C operation temperature range
Optional Plastic case
EMI complies with EN55022 Class A
RR-series, DIL 24 package, pic. similar
OUTPUT SPECIFICATIONS
Voltage accuracy
EMC SPECIFICATIONS
Radiated Emissions
1%
EN55022
Class A
Line regulation
0.5%
Conducted Emissions (4)
EN55022
Class A
Load regulation
0.5%
1.5%
ESD
RS
EFT
CS
IEC61000-4-2
IEC61000-4-3
IEC61000-4-4
IEC61000-4-6
IEC61000-4-8
Perf. crit. B
Perf. crit. A
Perf. crit. B
Perf. crit. A
Perf. crit. A
(Output 3.3V / 3.3V Model)
Ripple & Noise (20 MHz bandwith) (1)
60 mV pk-pk
Indefinite (automatic recovery)
0.02%/°C
Short circuit protection
Temperature coefficient
Capacitor load (2)
PFMF
See table
ABSOLUTE MAXIMUM RATINGS (4)
INPUT SPECIFICATIONS
Voltage range
Max. input current
No-load input current
Input filter
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
See table
See table
See table
PI Type
24 modes
48 modes
Lead soldering temperature
-0.7 ~ 40 VDC
-0.7 ~ 80 VDC
260°C
Input reflected ripple current (3)
35 mA pk-pk
(1.5 mm from case 10 sec.)
GENERAL SPECIFICATIONS
Efficiency (typ.)
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
See table
The information and specifications contained in this data sheet are believed
to be correct at time of publication. However, we accept no responsibility
for consequences arising from printing errors or inaccuracies.
Subject to change without notice.
I/O isolation voltage (3 sec.) Input/Output 1500 ~ 3500 VDC
Metal case / input & output
I/O isolation capacitance
I/O isolation resistance
Switching frequency
Humidity
1000 VDC
500 pF typ.
1000 M Ohm
typ. 266 kHz
95% rel. H
NOTE
1) Typical value at nominal input voltage and full load.
2) Tested by nominal Vin and constant resistor load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH.
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
5) It´s recommended to add C1 (68 F), C2 (33 F), L (12 H) in
input end to achieve EN55022 conducted Class A.
Reliability calculated MTBF (MIL-HDBK-217F)
Safety standard (designed to meet)
> 1.121 Mhrs.
IEC 60950-1: 2001
PHYSICAL SPECIFICATIONS
Case material
Nickel-coated copper
Non-conductive black plastic
(UL94V-0 rated)
Base material
Non-conductive black plastic
(UL94V-0 rated)
Pin material
Potting material
Weight
Ø 0.5 mm brass solder-coated
Epoxy (UL94V-0 rated)
Metal 17.0 g, Plastic 13.5 g
1.25“ x 0.8“ x 0.4“
Dimensions
The models listed are just for standard type. If you need a special
specification product, please contact our service.
Phone: +49 69 984047-0, mail to: info@rsg-electronic.de or use the forms
on www.rsg-electronic.de („Kontakt“).
ENVIRONMENT SPECIFICATIONS
Operating temperature (See derating curve)
Maximum case temperature
Storage temperature
-40°C~ 85°C
100°C
-40°C~125°C
Nature convection
Page: 1/3
Last update: 18.02.10
Cooling