RR5-S05/D05
5.0 Watt 4:1 regulated
single & dual output
■
■
■
■
■
■
■
DIP24, wide 4:1 input range
Full SMD technology
1500 VDC isolation up to 3500 VDC isolation
Continuous short circuit protection
Efficiency up to 81%
-25°C~85°C operation temperature range
Optional metal case
RR-series, DIL 24 package, metal version, pic. similar
OUTPUT SPECIFICATIONS
Voltage accuracy
Line regulation
ABSOLUTE MAXIMUM RATINGS (4)
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
1%
0.5%
0.5%
Load regulation
Ripple & Noise (20 MHz bandwith) (1)
Short circuit protection
Temperature coefficient
Capacitor load (2)
60 mV pk-pk
Continuous
0.02%ꢀ°C
See table
24 modes
48 modes
Lead soldering temperature
-0.7 ~ 40 VDC
-0.7 ~ 80 VDC
260°C
(1.5 mm from case 10 sec.)
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
INPUT SPECIFICATIONS
Voltage range
Max. input current
No-load input current
Input filter
See table
See table
See table
PI Type
The information and specifications contained in this data sheet are believed
to be correct at time of publication. However, we accept no responsibility
for consequences arising from printing errors or inaccuracies.
Subject to change without notice.
Input reflected ripple current (3)
35 mA pk-pk
GENERAL SPECIFICATIONS
NOTE
Efficiency
See table, typ.
1) Typical value at nominal input voltage and full load.
2) Tested by nominal Vin and constant resistive load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH.
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
5) Operation under no-load conditions will not damage
IꢀO isolation voltage (3 sec.) Inputꢀoutput 1500~3500 VDC
Metal case ꢀ input & output
IꢀO isolation capacitance
IꢀO isolation resistance
Switching frequency
Humidity
1000 VDC
60 pF typ.
1000 M Ohm
100~400 kHz
95% rel. H
Reliability calculated MTBF (MIL-HDBK-217F)
Safety standard (designed to meet)
> 2.199 Mhrs. these devices. However they may not meet all listed
IEC 60950-1:2001 specifications.
6) It´s necessary to add minimum capacitor in output for
some single models. Please contact the service team for
detail value.
PHYSICAL SPECIFICATIONS
Case material
Non-conductive black plastic
(UL94V-0 rated)
Nickel-coated copper
Base material
Non-conductive black plastic
(UL94V-0 rated)
Ø 0.5 mm brass solder-coated
Epoxy (UL94V-0 rated)
Metal 15 g, plastic 12.5g
1.25“ x 0.8“ x 0.4“
The models listed are just for standard type. If you need a
special specification product, please contact our service.
Phone: +49 69 984047-0, mail to: info@rsg-electronic.de
or use the forms on www.rsg-electronic.de („Kontakt“).
Pin material
Potting material
Weight
Dimensions
ENVIRONMENT SPECIFICATIONS
Operating temperature (See derating curve) -25°C~ 85°C
-25°C~ 71°C (For 100% load)
Maximum case temperature
Storage temperature
Cooling
100°C
-40°C~125°C
Nature convection
Page: 1ꢀ3
Last update: 18.02.09