APPLICABLE STANDARD
-25 C TO +85 C
-10
C TO +60 C
OPERATING
STORAGE TEMPERATURE
RANGE
RATING
TEMPERATURE RANGE
VOLTAGE
AC 500 V , DC 700 V
10 A
CURRENT
APPLICABLE CABLE
SPECIFICATIONS
TEST METHOD
ITEM
REQUIREMENTS
QT AT
CONSTRUCTION
X
X
X
X
GENERAL EXAMINATION
VISUALLY AND BY MEASURING INSTRUMENT.
CONFIRMED VISUALLY.
ACCORDING TO DRAWING.
MARKING
ELECTRIC CHARACTERISTICS
X
X
X
X
2 m MAX.
CONTACT RESISTANCE
CONTACT SHALL BE MEASURED AT DC
1
A
1000 M MIN.
INSULATION RESISTANCE
500 V DC.
X
X
VOLTAGE PROOF
1500 V AC FOR 1 min.
NO FLASHOVER OR BREAKDOWN.
MECHANICAL CHARACTERISTICS
0.003
CONTACT INSERTION AND
INSERTION AND WITHDRAWAL FORCES : 0.9 N MIN.
INSERTION AND WITHDRAWAL FORCES : 40 N MAX.
BY STEEL GAUGE.
φ2.362
X
X
0
-
-
WITHDRAWAL FORCES
CONNECTOR INSERTION AND
WITHDRAWAL FORCES
MEASURED BY APPLICABLE CONNECTOR.
LOCKING DEVICE WITH UNLOOK.
CONTACT RESISTANCE: 4 m MAX.
MECHANICAL OPERATION
2000 TIMES INSERTIONS AND EXTRACTIONS.
X
X
-
-
①NO ELECTRICAL DISCONTINUITY OF 10 s.
VIBRATION
SHOCK
FREQUENCY : 10 → 55 → 10(Hz) (1CYC, 5min),
SINGLE AMPLITUDE 0.75 mm, AT 10CYC, FOR 3 DIRECTIONS. ②NO DAMAGE, CRACK AND LOOSENESS, OF PARTS.
① NO ELECTRICAL DISCONTINUITY OF 10 s.
② NO DAMAGE, CRACK AND LOOSENESS, OF PARTS.
IN OPPOSITE DIRECTIONS OF EACH 3 DEMENSION AXIS FOR
3 TIMES AT 490 m/s2 DURATION OF PULSE 11 ms.
X
-
ENVIRONMENTAL CHARACTERISTICS
DAMP HEAT
EXPOSED AT 40 ℃, 90 TO 95 %, 96 h.
① INSULATION RESISTANCE: 100 MΩ MIN (AT DRY).
② NO DAMAGE.CRACK AND LOOSENESS OF PARTS.
① INSULATION RESISTANCE: 100 MΩ MIN..
② NO DAMAGE.CRACK AND LOOSENESS OF PARTS.
X
X
-
-
(STEADY STATE)
RAPID CHANGE OF TEMPERATURE TEMPERATURE -55→ R/T(1) → +85 → R/T ℃
TIME 30 → 2 TO 3 → 30 → 2 TO 3 min
UNDER 5 CYCLES.
EXPOSED IN 5 SALT WATER SPRAY FOR 48 h.
EXPOSED AT + 85 ℃ , 96 h.
CORROSION SALT MIST
NO HEAVY CORROSION RUIN THE FUNCTION.
NO DAMAGE,CRACK AND LOOSENESS OF PARTS.
NO DAMAGE,CRACK AND LOOSENESS OF PARTS.
X
X
X
X
-
-
-
-
DRY HEAT
COLD
EXPOSED AT - 55 ℃ , 96 h.
RESISTANCE TO SOLDERING
HEAT
SOLDER TEMPERATURE, +380±10℃ ,FOR IMMERSION
DURATION, 3 s.
NO DEFORMATION OF CASE OF EXCESSIVE LOOSENESS
OF THE TERMINALS.
SOLDERABILITY
SOLDERED AT SOLDER TEMPERATURE, +350±10℃ FOR
IMMERSION DURATION, 3 s.
WETTING ON SOLDER SURFACE.
X
X
-
-
NO SOLDER CLUSTER.
SEALING(2)
EXPOSED AT A DEPTH OF 1.8 m FOR 48 h.
NO WATER PENETRATION INSIDE CONNECTOR.
AIRTIGHTNESS(2)
APPLY AIR PRESSURE 17.6 kPa FOR 0.5 min TO INSIDE
CONNECTOR.
NO AIR BUBBLES FROM CONNECTOR INTERFACE.
X
-
COUNT
DESCRIPTION OF REVISIONS
DESIGNED
CHECKED
DATE
△
0
APPROVED
CHECKED
DESIGNED
REMARK
HY.KOBAYASHI
HY.KOBAYASHI
KN.IKEHARA
15.11.06
15.11.06
15.11.06
NOTES (1) R/T : ROOM TEMPERATURE
(2) SEALING AND AIRTIGHTNESS SHALL BE TESTED UNDER MATED CONDITION WITH
AN APPLICABLE CONNECTOR.
DRAWN
KN.IKEHARA
15.11.06
Unless otherwise specified, refer to JIS C 5402. (IEC 60512)
Note QT:Qualification Test AT:Assurance Test X:Applicable Test
DRAWING NO.
PART NO.
CODE NO.
ELC-110908-81-00
RM15WTPZ-4S(81)
SPECIFICATION SHEET
0
1/1
HIROSE ELECTRIC CO., LTD.
CL109-1612-8-81
△
FORM HD0011-2-1