REVISION BH
QSE-XXX-01-XXX-D-XXX
OPTION
No OF POSITIONS
-A: ALIGNMENT PINS
-020, -040, -060
(USE QSE-20-XX-D-XX-A)
(NOT AVAILABLE WITH -LC OPTION)
-LC: LOCKING CLIPS(SEE NOTE 14)
(USE LC-08-TM-01, SEE FIG 2, SHT 2)
(NOT AVAILABLE WITH -A OPTION)
-GP: GUIDE POSTS (SEE FIG 4, SHT 3)
(USE QSE-20-01-D-XX-X-GP)
(T & R PACKAGING: 40 POS MAX)
-K: POLYIMIDE FILM
DO NOT
SCALE FROM
THIS PRINT
*-080, *-100 (PER ROW)
(*= SEE NOTE & 17)
LEAD STYLE
-01: .1280[3.251]
(*= SEE NOTE 17)
(*= SEE NOTE 17)
PLATING SPECIFICATION
(USE K-DOT-.325-.450-.005)
(SEE FIG 3, SHT 2)
C
(SEE NOTES 8, 11 & 13)
-TR: TAPE & REEL (60 POS MAX)
(SEE FIG 8, SHT 5)
-F: 3µ" SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL
"A" REF
(40 POS MAX -GP OPTION)
-FL: FRICTION LOCKS
(USE C-126-21-F, T-1G2-01-F)
(SEE NOTE 8)
.7875 20.003 (TYP)
(SEE FIG 5, SHT 3)
-L: 10µ" SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL
(NOT AVAILABLE WITH -GP)
-RT1: RETENTION OPTION
(MUST USE -A OPTION)
19 EQ. SPCS
@ .0315 [0.800]
=.599[15.20]
(TYP)
.285 7.24
REF
(USE C-126-21-L, T-1G2-01-L)
-H: 30µ" GOLD IN CONTACT AREA,
3µ" GOLD ON TAIL
(USE QSE-20-01-D-XX-A-RT1 &
SUB-SC-05-01-FF)
(SEE FIG 6, SHT 4)
(USE C-126-21-H, T-1G2-01-G)
-C: 50µ" ELECTRO POLISHED SELECTIVE
GOLD IN CONTACT AREA,
02
.150 3.81
REF
(NOT AVAILABLE WITH -LC, -GP, OR -FL)
(NOT AVAILABLE WITH -100 POS)
-L: LATCHING OPTION (40 POS MAX)
(SEE FIG 7, SHT 4)
MATTE TIN ON TAIL
.245 6.22
REF
(USE C-126-21-C, T-1G2-01-L)
-STL: 30µ" SELECTIVE GOLD IN CONTACT
AREA, TIN LEAD (90/10 ±5%) ON TAIL
(USE C-126-21-STL, T-1G2-01-STL)
-FTL: 3µ" SELECTIVE GOLD INCONTACT
AREA, TIN LEAD (90/10 ±5%) ON TAIL
(USE C-126-21-FTL, T-1G2-01-FTL)
-LTL: 10µ" SELECTIVE GOLD IN CONTACT
AREA, TIN LEAD (90/10 ±5%) ON TAIL
(USE C-126-21-LTL, T-1G2-01-LTL)
-S: 30µ" SELECTIVE GOLD IN CONTACT
AREA, MATTE TIN ON TAIL
(MUST USE -A OPTION)
(NOT AVAILABLE WITH -LC, -GP, -FL,
OR -RT1)
01
.6250 15.875
REF
.0975 2.477
REF
.0060 0.152 REF
ROW SPECIFICATION
-D: DOUBLE
(USE QSE-20-XX-D-XX)
.0225 0.571
REF
(USE C-126-21-S, T-1G2-01-L)
No OF BANKS
QSE-20-01-D-XX-A
SEE NOTE 15
"A"
.017±.005 0.43±0.13
(SEE NOTE 16)
.120 3.05
REF
.038 0.95
REF
"A"
.725 18.42
REF
.0030 0.076 REF
"B" REF
C
+.0030
-.0010
+0.076
3.251
-0.025
.1280
+.004
-.002
+0.10
4.24
-0.05
.167
(SEE NOTE 6 & 7)
T-1G2-01-XXX
C
.105 2.67
REF
C
L
SEE TABLE 1
C
.064 1.62 REF
NOTES:
.295 7.491
.035 0.89 REF
C
1.
REPRESENTS A CRITICAL DIMENSION.
2. MINIMUM CONTACT RETENTION: 8 OZ
3. MINIMUM GROUND PLANE RETENTION: 8 OZ
4. PARTS ARE MOLDED TO POSITION.
5. DELETED.
6. MAXIMUM VARIANCE: .002[0.51].
7. DIMENSION APPLIES TO CONTACTS & GROUND PLANE.
8. -L PLATING CAN BE SUBSTITUTED FOR -F PLATING, -G PLATED GROUND
PLANE CAN BE SUBSTITUTED FOR -F PLATED GROUND PLANE.
9. GROUND PLANE PRESS HEIGHT MUST BE .003 [0.08] LESS THAN THE MAX HEIGHT
OR .001 [0.03] GREATER THAN THE MINIMUM HEIGHT OF THE SOCKETS.
10. MINIMUM SUB-SC-05-01-XX RETENTION: 1 LB IN BODY.
11. MAY SUB C-126-01-XXX FOR C-126-21-XXX.
12. NOTE DELETED.
13. FOR -080, -100 POSITIONS USE C-269-11-XXX. DO NOT SUB C-126.
14. DUE TO THE HIGH AMOUNT OF INSERTION FORCE NEEDED, THE -LC OPTION
IS NOT COMPATIBLE WITH AUTO PLACEMENT.SAMTEC RECOMMENDS
MANUAL PLACEMENT FOR ALL ASSEMBLIES WITH THE -LC OPTION.
15. SIDE WALLS ARE RIBBED AS NECESSARY TO CONTROL BOW.
16. CHECK ONCE PER BANK ALTERNATING SIDES FOR MULTIPLE BANK PARTS.
17. AVAILABLE FOR EXISTING CUSTOMERS ONLY.
.007 0.18 REF
C-126-21-XXX
(SEE NOTE 13)
FIG 1
SECTION "A"-"A"
-A: ALIGNMENT PIN OPTION
(QSE-060-01-XXX-D-A SHOWN)
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
ANGLES
2
.XX: .01[.3]
520 PARK EAST BLVD, NEW ALBANY, IN 47150
.XXX: .005[.13]
PHONE: 812-944-6733
FAX: 812-948-5047
code 55322
.XXXX: .0020[.051]
e-Mail info@SAMTEC.com
MATERIAL:
DO NOT SCALE DRAWING
SHEET SCALE: 1.5:1
DESCRIPTION:
INSULATOR: LCP, UL94V-0; COLOR: BLACK
CONTACT: PHOS BRONZE
GROUND PLANE: PHOS BRONZE
.8mm DOUBLE ROW HS SOCKET ASSEMBLY
DWG. NO.
QSE-XXX-01-XXX-D-XXX
BY:
ERIC M
05/20/1999 SHEET 1 OF 5
F:\DWG\MISC\MKTG\QSE-XXX-01-XXX-D-XXX-MKT.SLDDRW
5秒后页面跳转
解析光耦仿真器：升级光耦合器技术的必要性
英伟达新一代Blackwell GPU过热问题致交付延迟
国产厂商思特威CMOS图像传感器芯片单月出货超1亿颗，技术创新引领行业发展
台积电5nm和3nm产能利用率达100%，半导体行业景气度持续攀升
微信公众号
抖音公众号
浙公网安备 33010502006866号 浙ICP备10014259号-119
营业执照ICP证
数据手册
如果您发现信息不准确，
